Senect O2S-20-SC Manual Download Page 3

Page: 3 / 24

Table of contents

Product type .................................................................................. 2

Table of contents ........................................................................... 3

General Security Notes .................................................................. 5

Intended use .................................................................................. 7

Getting started .............................................................................. 8

Getting started – Short version ................................................... 11

Maintenance and cleaning .......................................................... 12

Cleaning ................................................................................... 12

Sensor disinfection .................................................................. 12

Recalibration ........................................................................... 13

Oxygen signal: 1-Point-calibration .......................................... 15

Short-version: Oxygen signal: 1-Point-calibration ................... 17

Oxygen signal: 2-Point-Calibration .......................................... 17

Temperature: 2-Point-Calibration ........................................... 18

Sensor Error ............................................................................. 19

Salinity / Conductivity correction ............................................ 20

Technical data ............................................................................. 22

Information about the correct disposal ...................................... 23

Guarantee .................................................................................... 24

Summary of Contents for O2S-20-SC

























Search results

Summary of Contents for O2S-20-SC

Reviews:

Related manuals for O2S-20-SC

Brands by name

Popular brands

Senect O2S-20-SC, Manual

Search results

Summary of Contents for O2S-20-SC

Reviews:

Related manuals for O2S-20-SC

Brands by name

Popular brands