manualshive.com logo in svg

Seneca ZC-24DO, Installation Manual

The Seneca ZC-24DO is a cutting-edge device designed to meet all your automation needs. With its advanced features and user-friendly interface, it guarantees seamless operation. Ensure a hassle-free installation of this product by downloading the free installation manual from our website, giving you access to expert guidance at your fingertips.

Share
Download
background image

DIGITAL OUTPUTS

MI001523-E

ENGLISH 5/8

Digital Outputs Connections from terminals

The total current entering on power supply terminal must be limited to 12 A with quick-break fuse or

quivalent protection.

Digital Outputs Connections from connectors (module rear side)

Connection suggested to supply 24 V relays. The total current entering on power supply terminal must be

limited to 0.6 A with quick-break fuse or equivalent protection. Max. current for each output: 25 mA.

IDC10: DOUT17..DOUT24

IDC20: DOUT1..DOUT16

Summary of Contents for ZC-24DO









Reviews:

No comments

Related manuals for ZC-24DO

M-system M6 Series Instruction Manual preview
M6 Series
Brand: M-system Pages: 3
M-system 60C Instruction Manual preview
60C
Brand: M-system Pages: 13
texet TR-3003 User Manual preview
TR-3003
Brand: texet Pages: 28
Panasonic SC-HC402 Operating Instructions Manual preview
SC-HC402
Brand: Panasonic Pages: 28
rav KPH 370.70 LIKT Translation Of The Original Instructions preview
KPH 370.70 LIKT
Brand: rav Pages: 82
Commax CDV-70A User Manual preview
CDV-70A
Brand: Commax Pages: 8
NA-DE M2307ADT User Manual preview
M2307ADT
Brand: NA-DE Pages: 18
M-system R7ML-EA8 Instruction Manual preview
R7ML-EA8
Brand: M-system Pages: 3
SPINOGY Xcool Operating Manual preview
Xcool
Brand: SPINOGY Pages: 27
Keithley KUSB-3160 Getting Started Manual preview
KUSB-3160
Brand: Keithley Pages: 59
H2flow levelsmart User Instruction Manual preview
levelsmart
Brand: H2flow Pages: 16
inveo RFID-USB-DESK Reader User Manual preview
RFID-USB-DESK Reader
Brand: inveo Pages: 11
Upright SB47JRT Operator'S Manual preview
SB47JRT
Brand: Upright Pages: 68
Jupiter Avionics wi JAC2-T32 Operating Manual preview
wi JAC2-T32
Brand: Jupiter Avionics Pages: 21
Wisdom AUDIO SYSTEM CONTROLLER SC-1 Owner'S Manual preview
AUDIO SYSTEM CONTROLLER SC-1
Brand: Wisdom Pages: 52
Ss Brewtech The Brew Bucket Quick Reference Manual preview
The Brew Bucket
Brand: Ss Brewtech Pages: 3
Ss Brewtech FTSs Pro Manual preview
FTSs Pro
Brand: Ss Brewtech Pages: 10
Arjohuntleigh Minstrel Instructions For Use Manual preview
Minstrel
Brand: Arjohuntleigh Pages: 32

Brands by name

Popular brands

Load more brands