background image

ENGLISH 3/16

MI004202-E

Errors referred to maximum
measuring range:

Calibration

Error

Thermal

Coefficient

Linearity

Error

EMI

Voltage or current input

0.1%

0.01%/°K

0.05%

<1%

TC Input: J, K, E, T, N

0.1%

0.01%/°K

0.2°C

<1% (1)

TC Input: R, S

0.1%

0.01%/°K

0.5°C

<1% (1)

TC Input: B

(2)

0.1%

0.01%/°K

1.5°C

<1% (1)

Cold junction compensation
(to TC Input)

2°C in ambient range from 0 to 50°C.

Potentiometer / Resistor Input

0.1%

0.01%/°K

0.1%

<1%

Thermoresistance RTD Input:
P

00, P 500, P 1000, N 100 (3)

T

T

T

I

1

0.1%

0.01%/°K

0.02% (se t > 0°C)
0.05% (se t < 0°C)

<1% (4)

Voltage output

(5)

0.3%

0.01%/°K

0.01%

(1) Influence of cable resistance 0.1 V/ .

m

W

(2) Output zero if t < 250 °C.
(3) All the values have to be calculated on the resistive value..
(4) Influence of cable resistance 0.005%/ max 20 .

W

W

(5) Values to be added to the errors of the selected input.

INSULATIONS 1500V

A

STANDARDS

The module complies with the following standards:

EN61000-6-4 (electromagnetic emission,
in industrial environment)
EN61000-6-2 (electromagnetic immunity,
in industrial environment)
EN61010-1 (safety)
Notes:
- Use with copper conductor.
- Use in Pollution Degree 2 Environment
- Power Supply must be Class 2
- When supplied by an Isolated Limited Voltage and/or

Limited Current power supply, a fuse rated max 2.5 A
shall be installed in the field.

1500 V

A

insulating voltage is among:

- power supply
- analog input
- analog output / digital input/ output

3.3 CONNE

ION

CT

S

USB Interface

Micro USB connector (frontal panel)

3.4 POWER SUPPLY

Supply Voltage

10-40 V , 19-28 V

50-60 Hz,

C

A

through screw terminals: 2 – 3

Power supply unit

Classe 2

Power consumption

1.6 W @ 24 V

with output 20 mA;

C

Max: 2.5 W

3.5 MODULE CASE

Case

PA6, black color

Dimensions

Width L=100mm; Height H=112mm; Depth W=17,5mm

Board terminals

Removable 3 way screw terminals: pitch 5.08mm, section 2.5mm

2

Protection class

IP20

3.6 ENVIRONMENTAL CONDITIONS

Operating
Temperature

-10°C – +60°C (UL: -10°C – +60°C)

2

3

4

5

6

USB

POWERSUPPLY

I / O

DIGITAL

1

UNIVERSAL

INPUT

ANALOG

OUT

10

11

12

9
8
7

1500 V

A

Summary of Contents for Z109REG2









Reviews: