Seneca Z-DAQ-PID User Manual Download Page 7 | Manualshive

Page: 7 / 24

background image

USER MANUAL – Z-DAQ-PID

7

PT500

-200°C..750°C

NI100

-60°C..250°C

4. Operation Modes

There are six possible functioning modalities for the Z-DAQ-PID, with reference to the following
figure:

- conversion with PID, analog output

- conversion with PID, ON/OFF output

- conversion without PID, analog output

- conversion without PID, ON/OFF output

- manual (constant output), analog output

- manual (constant output), ON/OFF output

With reference to the following figure, the lowest part shows the Z-DAQ-PID setting procedure in
three steps: input setting, operating modality setting, output setting.

In particular, there are three operating modes, each of them allows to supply a ON/OFF output or
an analog output:

«
...
5
6
7
8
9
...
»

Summary of Contents for Z-DAQ-PID

























Reviews:

No comments

Related manuals for Z-DAQ-PID

Brand: M&S Systems Pages: 16

dmc1 Finish-Out

Brand: M&S Systems Pages: 24

Brand: M&S Systems Pages: 24

Brand: Omega Pages: 44

Brand: Panasonic Pages: 28

Brand: Clarke Pages: 8

Brand: auna multimedia Pages: 124

Brand: Reliable Pages: 6

Brand: R. Beck Maschinenbau Pages: 34

Brand: SymCom Pages: 8

Brand: Ravaglioli Pages: 102

Brand: red lion Pages: 8

Brand: CyberData Pages: 2

AeGIS NPB9000P Series

Brand: PACH & COMPANY Pages: 49

Brand: Supersonic Pages: 6

Quad-MC EV9628-28

Brand: Everpure Pages: 2

Brand: M-E Pages: 28

MAJIC ATTIC LIFT

Brand: Majic Stairs Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands