EN-6
EN
Masticating Slow Juicer
SSJ 4041BK / SSJ 4042RD / SSJ 4043WH
2015
04/2015
THE PRINCIPLE AND ADVANTAGES OF A MASTICATING SLOW JUICER
•
The operating principle of this juicer is based on a system where ingredients are juiced slowly .
The auger first coarsely masticates the inserted ingredients and in the subsequent phase juice is
separated from the pulp . Juice pressed out in this way contains minimal fibre content and so is
characterised by a high purity, it is slower to oxidise and retains valuable vitamins and enzymes . The
strainer is automatically cleaned during operation and so it is not excessively clogged and is easier
to clean after use .
•
This juicer is suitable for juicing both soft and hard fruits and vegetables such as citrus fruits,
currants, gooseberries and other berries, apples, pears, carrots, beetroot, cucumbers, pineapple,
melon, etc . It can even handle leafy vegetables, however we recommend to process them together
with other fruits and vegetables .
•
It is not particularly suitable for juicing purely leafy vegetables, overripe fruits or floury apples .
BEFORE FIRST USE
1 . Remove all packaging materials from the appliance and its accessories .
2 . Thoroughly wash all removable parts (pusher A
1
, feed tube with hopper and lid A
2
, auger A
3
,
stainless steel strainer A
4
, strainer holder A
5
, juice collector A
6
, the juice jug A
8
and pulp
container A
0
) that come into contact with food in warm water using kitchen detergent . Then rinse
all these parts under clean running water and thoroughly wipe dry with a fine wiping cloth .
Attention:
No part of this juicer is designed to be washed in a dishwasher .
ASSEMBLING THE JUICER
1 . Place the base A
qs
on an even, dry and stable surface . During assembly, the appliance must be
turned off and disconnected from the el . power socket .
2 . Pick up the juice collector A
6
and turn it upside down . There is a black silicone plug on the bottom
of the collector at the pulp outlet A
9
. To prevent pulp from escaping out off the outlet A
9
, it is
necessary to properly seal the hole at the outlet A
9
with the silicone plug .
Note
:
To enable easier cleaning, the plug A
9
has a hole with a silicone plug .
3 . Put the juice collector A
6
to its correct position . Place it on the base A
qs
so that the projections
on the top side of the base A
qs
slide into the holes on the bottom of the juice collector A
6
. Turn
the juice collector A
6
clockwise to firmly connect it to the base A
qs
. When the juice collector A
6
is correctly attached to the base A
qs
, it cannot be lifted up separately .
4 . Insert the stainless steel strainer A
4
into the holder A
5
.
5 . Into the juice collector A
6
, place the holder A
5
with the inserted strainer A
4
so that the symbol
" " on the strainer A
4
is in alignment with the same symbol marked on the juice collector A
6
.
Push the holder A
5
with the strainer A
4
downwards .
6 . Insert the auger A
3
into the strainer A
4
and push it downwards . A correctly seated auger A
3
is
signalled by an audible click .
7 . Place the feed tube with hopper and lid A
2
on to the juice collector A
6
. If the hopper is removed
from the feed tube A
2
, first connect these two parts . Make sure that the open lock symbol marked
on the lid A
2
is aligned with the " " symbol on the juice collector A
6
. Then turn the feed tube
A
2
clockwise all the way . This will secure the lid A
2
on the juice collector A
6
. The " " symbol
marked on the juice collector A
6
will now be aligned with the closed lock symbol on the lid A
2
.
8 . Insert the pusher A
1
into the feed tube A
2
.
