Sencor SRV 9550BK, Translation Of The Original Manual

Page: 17 / 18

- 17 -
08/2020
Copyright © 2020, Fast ČR, a.s.
MANUAL CHARGING
■ When the vacuum cleaner is located away from the charging station and detects
a low battery voltage, the indicator on button
A5 ( ) and A6 ( ) will start
slowly pulsing yellow. Press button
A6
( ) on the vacuum cleaner or button
F12
( ) on the remote control The vacuum cleaner will automatically seek out the
charging station and start automatic charging as described in the previous chapter.
■ If the battery is so flat that the vacuum cleaner is unable to seek out the charging
station then it is necessary to dock the vacuum cleaner into the charging station
manually. Pick up the vacuum cleaner and manually place it into the charging
station so that the charging contacts on the underside of the vacuum cleaner and
the charging contacts on the charging station are connected. When the contacts are
connected, charging will start.
CARING FOR THE BATTERY
■ We recommend that you do not interrupt the charging cycle and maintain the
battery in a charged state.
■ Do not leave the vacuum cleaner completely flat for an unnecessarily long period
of time. A battery that is allowed to remain flat for a long time may self-discharge
below a permissible level and thereby cause irreparable damage to itself.
REPLACING THE BATTERY
■
Make sure that the vacuum cleaner is turned off. Turn the vacuum cleaner upside
down and remove the screws from the top part A18 of the battery.
■ Tilt the battery I1 out of the storage compartment I3 and pull the connector I2 to
disconnect it from the control board of the vacuum cleaner. To disconnect the
connector it is necessary to use greater force to overcome the safety mechanism
against spontaneous disconnection. Remove the battery.
■ Insert the connector of the new battery into the control board and place the battery
into the storage compartment being careful not to damage the connector cables.
Screw the top part of the battery into place.
Attention:
Use only the original battery type.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE AND SOLUTION
The vacuum cleaner
cannot be turned on.
Battery is almost or completely flat. Charge the battery.
Manually place the vacuum cleaner on to the charging
station.
The ambient temperature is too low or too high (lower than
0 °C or higher than 50 °C). Locate the vacuum cleaner in
an environment with a temperature in the range from 0 °C
to 40 °C.
The vacuum cleaner
is running but it is
vacuuming dust and dirt
poorly or not at all.
The dust container is full. Empty it out.
The dust filter in the container is not properly installed or
is excessively soiled. Check the position and cleanliness of
the filter.
The central rotary brush is clogged with material or hair is
tangled on it, and it is not turning. Clean out the brush and
the suction hole.
The vacuum cleaner
is making an unusual
noise while cleaning.
The central rotary brush, side rotary brush or one of the
motorised wheels is wrapped with material or tangled into
an obstacle (cables, etc.).
The vacuum cleaner
travels only backwards
when it is turned on.
The vacuum cleaner was placed on a floor that is too dark.
Move the vacuum cleaner to a lighter-coloured floor and
start it again.
One of the bottom sensors is soiled. Clean the all the sensors.
The bristles on a rotary
brush are deformed and
do not sweep up dust
and dirt.
The bristles are worn out. Dip them in warm water to renew
their original shape. Contact the vendor or service centre and
order a new brush.
Cleaning did not
occur at
the scheduled time.
The battery was not sufficiently charged. Scheduled cleaning
will only start when the battery is charged to at least 30%.
The vacuum cleaner was completely off. After performing
scheduled cleaning, it must be in the stand-by or sleep
mode.
The vacuum cleaner
did not travel on to the
charging station.
The charging station is not connected to mains power.
Connect it.
The vacuum cleaner is too far away from the charging
station. Carry the vacuum cleaner by hand to the vicinity of
the charging station.
The charging station is not located according to the
instructions in this user's manual and the vacuum cleaner
has poor access to it.
The vacuum cleaner is in
the charging station but
is not charging.
Check that the charging station is connected to the power
grid. Clean the charging contacts on the charging station and
the vacuum cleaner.
The vacuum cleaner did
not connect to the Wi-Fi
network.
Weak Wi-Fi network signal or the vacuum cleaner is out of
its range.
Incorrectly entered password.
Your router transmits in the 5 GHz broadcast band but your
vacuum cleaner can only receive signals in the 2.4 GHz
broadcast band.
Indicator on buttons
A5
( ) and
A6
( )
is rapidly flashing red.
The control system of the vacuum cleaner has detected
a problem, that may include the vacuum cleaner being lifted
off the ground, the dust container / water tank sliding out of
the vacuum cleaner during the charging process, the wheels
or brushes becoming blocked during operation, etc. Attempt
to identify what has caused the problem and attempt to fix
it. If the red flashing of the indicators persists, try turning
the vacuum cleaner completely off and then on again
with button
A5 ( ). If even this fails to help, contact an
authorised service centre.
CLEANING AND MAINTENANCE
■
Prior to cleaning, always turn off the vacuum cleaner by holding down button
A5
( ).
■ For cleaning, never use abrasive cleaning products, solvents, etc.
■ Neglecting cleaning and maintenance may negatively affect the working order of
the vacuum cleaner and lead to its reduced performance.
Attention:
When turning the vacuum cleaner upside down for maintenance
tasks, ensure that it does not fall out of your hands on to the
floor or that you do not damage its laser sensor A3 when putting
it down. We recommend placing the vacuum cleaner on to
a suitable soft surface.
DUST CONTAINER AND DUST FILTER
■ Empty out the dust container after every use and clean it regularly. Push down
latch
C6
to slide the dust container
C1
out of the vacuum cleaner, slide out the filter
holder C2 a tip the dust and dirt out of the container and filter.. For hygiene reasons,
we recommend doing this away from living areas.
■
Pull the holder
C5
to remove it and then remove the dust filter
C4
from it. Tap out
the dust filter and its holder or clean these parts using the brush H1 . Check the
condition of the filter and if damaged, replace it with a new one.
■
Tilt out the fine filter
C3
out of the holder
C2
and clean carefully using a brush.
■ In the event of greater soiling, the dust container and the filter holder can be
completely washed under running water. After washing them, it is necessary to
allow all the components to dry completely.
Attention:
Do not wash the main container, the dust container or the dust
filter in a dishwasher. The dust filter
C4
must not be washed using
water.
Before putting the vacuum cleaner back into operation, check
that the dust filter is in its location. Otherwise the vacuum cleaner
may be damaged.
■ Assemble all the parts to the initial state and slide the main container back into the
vacuum cleaner.
WATER TANK WITH THE DUST CONTAINER
■
Empty out the dust container
A5
contained inside the water tank
D1
after every use
and clean it regularly. Push down the latch D7 to release the water tank from the
vacuum cleaner. Push down the latch D6 to slide the dust container out of the water
tank, open it and tip out the dirty material. For hygiene reasons, we recommend
doing this away from living areas.
■ Pull out the dust filter D4 and tap it out or clean it using the brush H1 . Check the
condition of the filter and if damaged, replace it with a new one.
■ Use a damp cloth to also clean out the inside of the dust container. In the event of
greater soiling, the water tank and the dust container can be completely washed
under running water. After rinsing both containers, it is necessary to allow them
to dry completely.
Attention:
Do not wash the assembled water tank, the dust container or the
dust filter in a dishwasher. The dust filter D4 must not be washed
using water.
Before putting the vacuum cleaner back into operation, check
that the dust filter is in its location. Otherwise the vacuum cleaner
may be damaged.
MOP
■ After every dry or wet wiping, remove the mop fabric from the holder, wash it by
hand in lukewarm water with the addition of a small amount of gentle washing
powder and allow it to dry naturally.
■ Wipe the mop holder with a lightly dampened cloth or wash it under running water
and then dry thoroughly.