Sencor SRV 9550BK, Translation Of The Original Manual

Page: 16 / 18

- 16 -
08/2020
Copyright © 2020, Fast ČR, a.s.
■ When the direction button F6 or F7 is pressed, the robotic vacuum cleaner will turn
in the respective direction. To continuously turn the vacuum cleaner, hold down
button
F6
or
F7
. Releasing the button will stop the turning of the vacuum cleaner.
■ In the manual movement control mode, the robotic vacuum cleaner moves
according to the direction buttons and the front sensors in the bumper bar and
the sensors on the underside of the vacuum cleaner that prevent collisions with
obstacles and falling from stairs.
PAUSING THE CLEANING PROCESS
■ Press button A5 ( ) or F9 ( ) on the remote control at any time during the
cleaning process to stop the vacuum cleaner in the place where it is cleaning. Press
one of the above-mentioned buttons again to continue with the commenced
cleaning process. Pausing and restarting the cleaning process is accompanied by
a voice message.
USING THE MOP
Assembly
■ The mop is used for dry and wet wiping of hard floor surfaces combined with
vacuuming. It consists of the holder E1 and a mopping fabric E4 . However, the mop
is not intended for cleaning carpets.
■ Attach the mopping fabric to the holder E1 using the Velcro zip E3 on the holder.
■ Insert the holder with the fabric into the groove E5 located on the underside of the
water tank
D1
. Then insert the water tank
D1
assembled in this way into the vacuum
cleaner. For wet wiping (mopping) it is necessary to first pour water into the water
tank, see description below.
Attention:
The mop holder can only be attached to the water tank D1 .
Therefore, only use the holder and the water tank that is intended
for this robotic vacuum cleaner model.
Always attach the mop holder on to the water tank away from
from the vacuum cleaner, and only thereafter insert the tank with
the holder into the vacuum cleaner. To attach the holder with the
mop to the tank when it is inserted in the vacuum cleaner would
require one to turn the vacuum cleaner upside down. This could
result in damage to the laser sensor A3 or other parts of the
vacuum cleaner, e.g. by being dropped on the floor or the sensor
being excessively pushed in against the floor.
Dry wiping of floors
■
Dry wiping is used for removing fine dust and floor polishing.
■ Insert the assembled water tank D1 with the mop holder into the vacuum cleaner.
There must be no water poured into the water tank D1 .
■ Start the vacuum cleaner.
Wet wiping of floors
■ Wet wiping (mopping) is used for wiping away minor dirt and floor polishing. It will
not, however, remove resistant stains such as dry stains from coffee, etc.
■
Assemble the water tank
D1
with the mop holder. Tilt open the rubber cap
D2
on
the water tank and fill it up with clean water through the filling hole D3 . Properly
push the cap back on and wipe away any water remaining on the water tank.
■
Insert the water tank
D1
into the vacuum cleaner.
■ Start the vacuum cleaner.
Note:
The vacuum cleaner is equipped with an electronically-controlled water
pump that automatically doses the water on to the fabric and also stops
dosing water at the end of the cleaning process to prevent water from
leaking on to the floor or the charging station.
For wiping, we recommend using clean water. If you use a cleaning agent,
it may foam up and thereby worsen the dripping of the water on to the
fabric, or potentially cause smudges on the floor after it dries.
Removing the mop from the water tank
■ If you wish to remove the holder with the mop from the water tank, first take the
water tank out of the vacuum cleaner and turn it upside down.
■
Pressing latches
D7
will release the holder with the mop, which can then be easily
pulled out of the groove in the water tank.
SCHEDULED CLEANING
Note:
The scheduled cleaning time setting is based on the system time of the
vacuum cleaner. Therefore, before setting the scheduled cleaning time,
it is necessary to correctly set the system time as described in chapter
SETTING THE SYSTEM TIME.
■ This function enables scheduling the vacuum cleaner to automatically start cleaning
at a certain time once per day.
■ When the smart device application is used to control the vacuum cleaner, it is
possible to schedule a different cleaning time for each individual day of the week.
Please follow the instructions in the application.
Setting scheduled cleaning:
■ In the stand-by mode or in the charging in the charging station mode, hold down
button
F3 ( ) until the hours setting value starts flashing on the display F2 .
■
Using buttons
F5
( ) or
F8
( ) set the time value. Toggle between the hour and
minute numbers using buttons F6 ( ) or F7 ( ).
■ Confirm the set time by pressing button F3 ( ). Two beeps will be made and
the set time will be saved to memory as the automatic cleaning time. The vacuum
cleaner will clean at this time every day.
■ In the event that no change is made within 10 seconds, the appliance will beep 2x
and the scheduled cleaning time setting mode will automatically be cancelled. Time
will not be stored in memory.
Note:
If you wish to use automatic cleaning, then it is appropriate to leave the
vacuum cleaner in the charging station.
Cancelling scheduled cleaning
■ Hold down button F3 ( ). The set automatic cleaning time will start flashing on
the display.
■
Using the arrows
F5
to
F7
set the value 00:00.
■ Hold down button F3 ( ). Two audible beeps will be heard. Thereby the set
cleaning time has been cancelled.
CONTROLLING THE VACUUM CLEANER USING THE MOBILE
APPLICATION
■
The vacuum cleaner can also be controlled using a smartphone or tablet. The
application enables you to select the cleaning mode, stop the cleaning process or
send the vacuum cleaner to the charging station; it provides an overview of how
much time was spent cleaning and about the condition of the vacuum cleaner.
■ The application is freely available in the Apple App Store or Google Play Store . This
link for this application is found in the picture part of this user's manual.
Note:
The robotic vacuum cleaner supports Wi-Fi in the 2.4 GHz frequency band.
If unsure about which standards are used by your Wi-Fi network and your
router, please contact your internet service provider or the manufacturer
of the router.
■ After downloading and installing the application on the smart device, set the
vacuum cleaner to the network configuration mode by simultaneously holding
down buttons
A5 ( ) and A6 ( ) for more than 3 seconds. Two beeps and
a voice message about network configuration will be made. The indicator on
buttons
A5
and
A6
will start flashing blue. If you wish to cancel the network
configuration mode, press any button on the remote control or one of the buttons
A5 and A6 on the vacuum cleaner.
■
Launch the application. After registration, the application will guide you through
the process for connecting the vacuum cleaner to your Wi-Fi network.
CHARGING THE ROBOTIC VACUUM CLEANER
AUTOMATIC CHARGING
■
When the vacuum cleaner finishes cleaning or when it detects a low battery voltage
during operation, the indicator on button
A5 ( ) and A6 ( ) will start slowly
pulsing yellow. A voice message will be sounded and the vacuum cleaner will
automatically start to seek out the charging station.
■ In order for it to find it and dock, it needs to find the infrared signal transmitted
by the charging station. For this reason, we recommend leaving the charging
station constantly connected to the power grid and located in accordance with the
instructions provided in chapter LOCATION OF THE CHARGING STATION.
■
In the event that the vacuum cleaner is for some reason unable to find the charging
station (too many obstacles, incorrect location, etc.) a voice message will be made
requesting the vacuum cleaner to be placed in the vicinity of the charging station.
■
After docking in the charging station, the charging cycle will commence. A full
charge takes approximately 5 hours. The actual charging time depends on the
power level of the battery. A fully charged battery will provide up to 200 minutes
of operation.
■ During the charging process, the indicator light in buttons A5 ( ) and A6 ( )
will continue to slowly pulse in yellow colour. When the battery is fully charged, the
indicator lights on both buttons will remain permanently lit blue and the process
will end automatically.
■ In the event that the charging contacts are disconnected during the charging cycle,
the vacuum cleaner will move away from the charging station and then re-dock
itself to resume the charging process, unless it is prevented from doing so by an
obstacle. In the event of a power outage, the charging cycle will be interrupted and
will continue after the power supply is renewed. In the event that the maximum
charging current is exceeded, the charging station will automatically interrupt the
charging cycle.
Note:
When the vacuum cleaner is docked in the charging station, it is not
possible to turn it off completely by pressing button
A5 ( ) on the
vacuum cleaner or button F9 ( ) on the remote control. If this is
attempted, a voice message will inform you that the vacuum cleaner must
first be removed from the charging station.