- 9 -
08/2020
Copyright © 2020, Fast ČR, a.s.
■
Set the vacuum cleaner to the stand-by mode by pressing button
A2
on the vacuum
cleaner or button
C4
on the remote control at any time while it is running.
SLEEP MODE
■
The sleep mode serves to save the battery's capacity. The vacuum cleaner enters
sleep mode either automatically after five minutes of inactivity or when it is unable to
dock in the charging station. The indicator on button
A2
will turn off and the vacuum
cleaner will automatically switch to the sleep mode.
■
To wake the vacuum cleaner from the sleep mode, press button
A2
on the vacuum
cleaner or button
C4
on the remote control.
Note:
When the vacuum cleaner is in sleep mode, it is not possible to wake it
up using the mobile phone application. In sleep mode, it reacts only to
buttons
A2
or
C4
on the remote control.
Attention:
The battery is gradually discharged also in the sleep mode,
though slowly. If the vacuum cleaner is left in the sleep mode
for an extended period of time (several days), the battery may
become fully discharged. If this happens, the vacuum cleaner will
not react to any button that is pressed and it will be necessary
to place it into the charging station so that it can recharge itself.
GUIDE TO LIGHT INDICATORS
Colour of the indicator in button A2
Meaning
White – permanently lit
Ready for operation
White – flashing
Charging / connecting to Wi-Fi
Red – flashing
Low battery voltage / problem
TURNING OFF
■
If you wish to turn the vacuum cleaner completely off, open the cover
A3
and set
the main switch
A7
to the OFF position. The indicator in button
A2
will turn off and
the power supply will be shut off. When the vacuum cleaner is turned off, it will not
respond to any button.
TURNING VOICE MESSAGES ON/OFF
■
If you prefer not to have the robotic vacuum cleaner make system voice messages,
deactivate this function pressing button
C7
on the remote control.
■
If you wish to reactivate the voice messages, press button
C7
again.
SELECTING THE CLEANING MODE
■
Before starting the cleaning process, check that the entry door into your apartment
or house is closed. From the floor surfaces, remove clothing, paper, plastic bags, toys,
power or extension cords and other items that the vacuum cleaner could suck in or
catch. Lift curtains and drapes that reach to the floor so that the vacuum cleaner does
not catch them.
Tip:
When vacuuming in a new environment for the first time, carefully
observe the movement of the vacuum cleaner. You can thereby recognise
problematic obstacles and remove them for the next cleaning session.
AUTOMATIC CLEANING MODE
■
Press button
A2
on the vacuum cleaner or button
C4
on the remote control. The
robotic vacuum cleaner will enter the automatic cleaning mode, in which it effectively
combines various routes to achieve an optimal clean of the entire floor area. As soon
as the vacuum cleaner finishes cleaning, it will seek out the charging station and dock
there to recharge.
SMALL AREA INTENSIVE CLEANING MODE
■
Press button
C5
on the remote control. The vacuum cleaner will enter the cleaning
mode, where it moves along a spiral up to a distance of approximately one meter and
then returns along the spiral back to the initial point, thoroughly cleaning the given
area. As soon as the vacuum cleaner finishes cleaning, it will seek out the charging
station and dock there to recharge.
ALONG-THE-WALLS CLEANING MODE
■
Press button
C6
on the remote control. The vacuum cleaner will enter the along-the-
walls cleaning mode, in which it moves along the perimeter of the room and the
motorised side rotary brushes sweep out the dirt along the walls, furniture corners to
achieve a perfect clean. As soon as the vacuum cleaner finishes cleaning, it will seek
out the charging station and dock there to recharge.
Note:
Other cleaning modes are available via the smart device application,
see chapter CONTROLLING THE VACUUM CLEANER USING THE MOBILE
APPLICATION
CHANGING SUCTION POWER
■
Based on the level of soiling of the vacuumed area or based on the time of day that
the robotic vacuum cleaner is used (e.g. later at night or early morning), it is possible
to use buttons
C8
and
C9
on the remote control to simply increase or decrease the
suction power.
MANUALLY CONTROLLING THE MOVEMENT OF THE VACUUM
CLEANER
■
The direction buttons
C3
can be used to manually control the movement of the
robotic vacuum cleaner on the floor. When the vacuum cleaner is moved on the floor,
the operation of the side rotary brushes is synchronised with the movement of the
motorised wheels.
Note:
When the vacuum cleaner is controlled manually, the vacuum cleaning
function is turned off. Nevertheless, the sensors on the vacuum cleaner
remain functional and prevent collisions with obstacles and falling from
stairs.
■
When the direction buttons forward or reverse are pressed, the robotic vacuum
cleaner will move in the respective direction. For continuous movement forward,
hold down the respective button. Releasing the button will stop the movement of
the vacuum cleaner.
■
When the direction button left or right is pressed, the robotic vacuum cleaner will turn
in the respective direction. To continuously turn the vacuum cleaner, hold down the
respective button. Releasing the button will stop the turning of the vacuum cleaner.
PAUSING THE CLEANING PROCESS
■
Press button
A2
or
C4
on the remote control at any time during the cleaning process
to stop the vacuum cleaner in the place where it is cleaning. Press one of the above-
mentioned buttons again to continue with the commenced cleaning process.
DRY AND WET WIPING
■
The system for wiping with the mop fabric is used for dry and wet wiping of hard floor
surfaces combined with concurrent vacuuming. The system consists of a water tank
A4
, holder
D3
and the mop fabric
D4
.
Attention:
The mop fabric is not intended for cleaning carpets.
The mop holder can only be attached to the water tank
A4
.
Therefore, only use the holder and the water tank that is intended
for this robotic vacuum cleaner model.
Always attach the mop holder on to the water tank away from
the vacuum cleaner, and only thereafter insert the tank with the
holder into the vacuum cleaner. To attach the holder with the
mop to the tank when it is inserted in the vacuum cleaner would
require one to turn the vacuum cleaner upside down. This could
result in damage to the camera
A5
or other parts of the vacuum
cleaner, e.g. by being dropped on the floor or the camera being
excessively pushed in against the floor.
Dry wiping of floors
■
Dry wiping is used for removing fine dust and floor polishing.
■
Attach the mopping fabric to the holder using the Velcro zip on the holder.
■
Insert the pins of the holder with the fabric into the holes
A15
located on the
underside of the water tank. Then insert the water tank assembled in this way into the
vacuum cleaner. There must be no water in the water tank.
■
Start the vacuum cleaner.
Wet wiping of floors
■
Wet wiping (mopping) is used for wiping away minor dirt and polishing floors. It will
not, however, remove resistant stains such as dry stains from coffee, etc.
■
Attach the mopping fabric to the holder using the Velcro zip on the holder.
■
Insert the pins of the holder with the fabric into the holes
A15
located on the
underside of the water tank.
■
Tilt open the rubber cap
D2
on the water tank and fill it up with clean water through
the filling hole. Do not fill past the maximum water level mark marked on the water
tank. Properly push the cap back on and wipe away any water remaining on the water
tank.
■
Then insert the assembled and filled water tank into the vacuum cleaner.
■
Start the vacuum cleaner.
Note:
The vacuum cleaner is equipped with an electronically-controlled water
pump that automatically doses the water on to the fabric and also stops
dosing water at the end of the cleaning process to prevent water from
leaking on to the floor or the charging station.
For wiping, we recommend using clean water. If you use a cleaning agent,
it may foam up and thereby worsen the dripping of the water on to the
fabric, or potentially cause smudges on the floor after it dries.
Removing the mop from the water tank
■
If you wish to remove the holder with the mop from the water tank, first take the water
tank out of the vacuum cleaner.
■
Remove the holder by pulling it from the underside of the water tank and pull the
mop fabric off the holder.
■
Tilt open the rubber cap
D2
on the water tank and pour out any remaining water.
