background image

Model 0205NANO Operation and Maintenance Manual

iv 

SEM | www.semshred.com

Disclaimer

Every care has been taken by the staff of SEM in compilation of the data contained in 
all training and informational materials (“collateral”) and in verification of its accuracy 
when published; however, the content of this collateral is subject to change without 
notice due to factors outside the control of SEM and this collateral should therefore 
be used as a guide only. The products referred to in these publications are continually 
improved through further research and development, which may lead to the alteration 
of information contained in this collateral. SEM does not accept any responsibility 
whatsoever for misrepresentation by any person whatsoever of the information 
contained in this collateral and expressly disclaims any and all liability and responsibility 
to any person, whether a reader/viewer of this collateral or not, with respect to claims, 
losses, damage, or any other matter, either direct or consequential, arising out of or in 
relation to the use and reliance upon any information contained or products referred 
to in this collateral. SEM does not warrant that the equipment will work properly in 
all environments and applications, and makes no warranty or representation, either 
implied or expressed, with respect to the performance, throughput, or maintenance 
requirements of the machine. Performance, throughput, and maintenance requirements 
vary depending on screen size, feed rate, and media type as well as operational 
procedures. Information in this collateral is subject to change without notice and does 
not represent a commitment on the part of SEM. SEM assumes no responsibility for any 
inaccuracies that may be contained in this collateral or any omissions that may have 
occurred. SEM makes no commitment to update or keep current the information in this 
collateral and reserves the right to make improvements to this collateral and/or to the 
products described therein at any time without notice. 

Proprietary Information: 

This document contains proprietary and confidential infor-

mation of SEM, and shall not be used, disclosed or reproduced, in whole or in part, for 
any purpose, without the prior written consent of SEM. Title in and to this document 
and all information contained herein remains at all times in SEM. This information is 
exempted from disclosure under FOIA, as amended.

Summary of Contents for 0205NANO














Reviews: