SELT Venetian Blind Z90 Technical And Operational Documentation Download Page 16 | Manualshive

Page: 16 / 58

background image

DT-E 1.4: SUN PROTECTION SCREEN – VENETIAN BLINDS Z90
Issue 2 / April 2017 / EN

page 16 / 58

Oval guide rail

Cube guide rail

Self-supporting bracket

Manner of installation



Slide the fixing element into guide rail channel.



Loosely secure self-locking nut until resistance appears.



Proper tightening should be performed with a wrench (10") and maximum 4 full turns (1440°).

NOTE

: bigger turn will result in tearing out the threaded stud!

1.

Measure and mark the spots for guide rail brackets
installation. Install the brackets.

Img. 1

2.

According  to  previous  measurements,  install  the
brackets  to  the  facade.  Number  of  brackets
depends  on  the  product  dimensions.  Imgs.  2-8.
During  installation  verify  the  dimensions  and
vertical  and  horizontal  alignement  of  the  brackets.
Correct if necessary.

Img. 2

«
...
14
15
16
17
18
...
»

Summary of Contents for Venetian Blind Z90



























































Reviews:

No comments

Related manuals for Venetian Blind Z90

Brand: Velux Pages: 9

Brand: Roto Pages: 80

Brand: Electra Pages: 16

Wood Line Series

Brand: Swiss Sonnenschutz Pages: 4

Brand: IKEA Pages: 4

Brand: Franken Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands