MANUAL DE INSTRUCCIONES
CÓDIGO 80412 REV 0
03/2021
Pag.: 21
J
.P. SELECTA s.a.u.
Autovía A-2 Km 585.1 Abrera 08630 (Barcelona) España
Tel 34 937 700 877 Fax 34 937 702 362
e-mail: [email protected] - website: http://www.grupo-selecta.com
1592036010 XW70LH GB r1.0 14.02.2014.docx
XW70LH
3/5
dFP Probe selection for defrost termination: nP
= no probe;
P1
=thermostat probe;
P2 =
evaporator probe;
P3
=configurable probe;
P4
= Probe on Hot Key plug.
dtE Defrost termination temperature
: (-50÷50 °C/
-58÷122°F) (Enabled only when EdF=Pb) sets the temperature measured by the evaporator
probe, which causes the end of defrost.
IdF Interval between defrost cycles
: (0÷120h) Determines the time interval between the
beginning of two defrost cycles.
MdF (Maximum) length for defrost
: (0÷255min) When
P2P = n
, (not evaporator probe: timed
defrost) it sets the defrost duration, when
P2P = y
(defrost end based on temperature) it sets
the maximum length for defrost.
dSd Start defrost delay
: ( 0÷99min) This is useful when different defrost start times are necessary
to avoid overloading the plant.
dFd Temperature displayed during defrost
: (
rt
= real temperature;
it
= temperature at defrost
start;
SEt
= set point;
dEF
= “dEF” label)
dAd MAX display delay after defrost
: (0÷255min). Sets the maximum time between the end of
defrost and the restarting of the real room temperature display.
Fdt Drip time
: (0
120 min) time interval between reaching defrost termination temperature and the
restoring of the control’s normal operation. This time allows the evaporator to eliminate water
drops that might have formed due to defrost.
dPo First defrost after start-up
: (y = immediately; n = after the IdF time)
dAF Defrost delay after continuous cycle
: (0
23.5h) time interval between the end of the fast
freezing cycle and the following defrost related to it.
FANS
FnC Fans operating mode
:
C-n
= runs with the compressor, OFF during defrost;
o-n
= continuous mode, OFF during defrost;
C-Y
= runs with the compressor, ON during defrost;
o-Y
= continuous mode, ON during defrost;
Fnd Fans delay after defrost:
(0÷255min) Interval between end of defrost and evaporator fans start.
Fct Temperature differential avoiding short cycles of fans
(0÷59°C; Fct=0 function disabled). If
the difference of temperature between the evaporator and the room probes is more than the
value of the Fct parameter, the fans are switched on.
FSt Fans stop temperature
: (-50÷50°C/122°F) setting of temperature, detected by evaporator
probe, above which fans are always OFF.
Fon Fan ON time:
(0÷15 min)
with
Fnc = C_n or C_y, (fan activated in parallel with compressor). it
sets the evaporator fan ON cycling time when the compressor is off. With Fon =0 and FoF
≠ 0
the fan are always off, with Fon=0 and FoF =0 the fan are always off.
FoF Fan OFF time:
(0÷15 min)
with
Fnc = C_n or C_y, (fan activated in parallel with compressor). it
sets the evaporator fan off cycling time when the compressor is off. With Fon =0 and FoF
≠ 0
the fan are always off, with Fon=0 and FoF =0 the fan are always off.
FAP Probe selection for fan management: nP
= no probe;
P1
=thermostat probe;
P2 =
evaporator
probe;
P3
=configurable probe;
P4
= Probe on Hot Key plug.
AUXILIARY THERMOSTAT CONFIGURATION (terms. 20-21) – OA4 = AUS
ACH Kind of regulation for auxiliary relay
:
Ht
= heating;
CL
= cooling
SAA Set Point for auxiliary relay:
(-50,0÷110,0°C; -58÷230°F) it defines the room temperature set
point to switch auxiliary relay.
SHy Differential for auxiliary output:
(0,1 ÷ 25,5°C / 1÷255 °F) Intervention differential for
auxiliary output set point.
With ACH = cL
AUX Cut in is SAA + SHy; . AUX Cut out is SAA
With ACH = Ht
AUX Cut in is SAA - SHy; . AUX Cut out is SAA
ArP Probe selection for auxiliary
: nP = no probe, the auxiliary relay is switched only by button;
P1
=
Probe 1 (Thermostat probe);
P2 =
Probe 2 (evaporator probe);
P3 =
Probe 3 (display probe);
P4 =
Probe 4 fourth probe.
Sdd Auxiliary relay off during defrost: n =
the auxiliary relay operates during defrost.
y =
the auxiliary relay is switched off during defrost.
ALARMS
ALP Probe selection for alarm
: nP = no probe, the temperature alarms are disabled;
P1 =
Probe 1
(Thermostat probe);
P2 =
Probe 2 (evaporator probe);
P3 =
Probe 3 (display probe);
P4 =
Fourth probe.
ALC Temperature alarms configuration:
(Ab; rE)
Ab
= absolute temperature: alarm temperature is given by the ALL or ALU values.
rE
=
temperature alarms are referred to the set point. Temperature alarm is enabled when the
temperature exceeds the “SET+ALU” or “SET-ALL” values.
ALU MAXIMUM temperature alarm
: (SET÷110°C; SET÷230°F) when this temperature is reached
the alarm is enabled, after the “ALd” delay time.
ALL Minimum temperature alarm
: (-50.0 ÷ SET°C; -58÷230°F when this temperature is reached
the alarm is enabled, after the “ALd” delay time.
AFH Differential for temperature alarm/ fan recovery:
(0,1÷25,5°C; 1÷45°F) Intervention
differential for recovery of temperature alarm. It’s also used for the restart of the fan when the
FSt temperature is reached
ALd Temperature alarm delay
: (0÷255 min) time interval between the detection of an alarm
condition and alarm signalling.
dAO Exclusion of temperature alarm at startup
: (from 0.0 min to 23.5h) time interval between the
detection of the temperature alarm condition after instrument power on and alarm signalling.
CONDENSER TEMPERATURE ALARM
AP2 Probe selection for temperature alarm of condenser: nP
= no probe;
P1
=thermostat probe;
P2 =
evaporator probe;
P3
=configurable probe;
P4
= Probe on Hot Key plug.
AL2 Low temperature alarm of condenser
:
(-55÷150°C) when this temperature is reached the LA2
alarm is signalled, possibly after the Ad2 delay.
Au2 High temperature alarm of condenser
:
(-55÷150°C) when this temperature is reached the
HA2 alarm is signalled, possibly after the Ad2 delay.
AH2 Differential for temperature condenser alarm recovery
:
(0,1÷25,5°C; 1÷45°F)
Ad2 Condenser temperature alarm delay
: (0÷255 min) time interval between the detection of the
condenser alarm condition and alarm signalling.
dA2 Condenser temperature alarm exclusion at start up
: (from 0.0 min to 23.5h, res. 10min)
bLL Compressor off with low temperature alarm of condenser
:
n = no:
compressor keeps on
working
; Y = yes,
compressor is switched off till the alarm is present, in any case regulation
restarts after AC time at minimum.
AC2 Compressor off with high temperature alarm of condenser
:
n = no:
compressor keeps on
working
; Y = yes,
compressor is switched off till the alarm is present, in any case regulation
restarts after AC time at minimum.
AUXILIARY RELAYS
tbA Alarm relay silencing (with oA3 or oA4=ALr):
n
= silencing disabled: alarm relay stays on till alarm condition lasts,
y
=silencing enabled: alarm relay is switched OFF by pressing a key during an alarm
oA3 Fourth relay configuration (1-3):
dEF, FAn:
do not select it!.
ALr
: alarm;
Lig
: light;
AuS
:
Auxiliary relay;
onF
: always on with instrument on;
db=
neutral zone;
cP2 =
second compressor;
dEF2:
do not select it!;.
HES:
. night blind
oA4 Fifth relay configuration (20-21):
dEF, FAn:
do not select it!.
ALr
: alarm;
Lig
: light;
AuS
:
Auxiliary relay;
onF
: always on with instrument on;
db=
neutral zone;
cP2 =
second compressor;
dEF2:
do not select it!;.
HES:
. night blind
AoP Alarm relay polarity:
it set if the alarm relay is open or closed when an alarm happens.
CL
=
terminals 1-2 closed during an alarm;
oP
= terminals 1-2 open during an alarm
DIGITAL INPUTS
i1P Digital input polarity (13-14): oP:
the digital input is activated by opening the contact;
CL:
the
digital input is activated by closing the contact.
i1F Digital input configuration (13-14): EAL
= external alarm: “EA” message is displayed;
bAL
=
serious alarm “CA” message is displayed.
PAL
= pressure switch alarm, “CA” message is
displayed;
dor
= door switch function;
dEF
= activation of a defrost cycle;
AUS
=not enabled;
Htr
= kind of action inversion (cooling – heating);
FAn
=
not set it; ES
=
Energy saving;
HdF
=
Holiday defrost (enable only with RTC);
onF =
to switch the controller off.
did
(0
255 min)
with
i1F= EAL or i1F = bAL digital input alarm delay (13-14):
delay between the
detection of the external alarm condition and its signalling.
with
i1F= dor: door open signalling delay
with i1F= PAL: time for pressure switch function:
time interval to calculate the number of
the pressure switch activation.
i2P 2
nd
digital input polarity (13-19): oP:
the digital input is activated by opening the contact;
CL:
the digital input is activated by closing the contact.
i2F 2
nd
digital input configuration (13-19): EAL
= external alarm: “EA” message is displayed;
bAL
= serious alarm “CA” message is displayed.
PAL
= pressure switch alarm, “CA” message is
displayed;
dor
= door switch function;
dEF
= activation of a defrost cycle;
AUS
=not enabled;
Htr
= kind of action inversion (cooling – heating);
FAn
=
not set it; ES
=
Energy saving;
HdF
=
Holiday defrost (enable only with RTC);
onF =
to switch the controller off.
d2d
(0
255 min)
with
i2F= EAL or i2F= bAL 2
nd
digital input alarm delay (13-19):
delay between
the detection of the external alarm condition and its signalling.
with
i2F= dor: door open signalling delay
with i2F= PAL: time for pressure switch function:
time interval to calculate the number of
the pressure switch activation.
nPS Pressure switch number:
(0
15) Number of activation of the pressure switch, during the “
did
”
interval, before signalling the alarm event (I2F= PAL).
If the nPS activation in the did time is reached, switch off and on the instrument to
restart normal regulation.
odc Compressor and fan status when open door:
no
= normal;
Fan
= Fan OFF;
CPr
=
Compressor OFF;
F_C
= Compressor and fan OFF.
rrd Outputs restart after doA alarm: no=
outputs not affected by the doA alarm;
yES =
outputs
restart with the doA alarm.
HES Temperature increase during the Energy Saving cycle:
(-30,0°C
30,0°C) it sets the increasing value of the set point during the Energy Saving cycle.
TO SET CURRENT TIME AND WEEKLY HOLIDAYS (ONLY FOR MODELS WITH RTC)
Hur
Current hour
(0 ÷ 23 h)
Min
Current minute
(0 ÷ 59min)
dAY Current day
(Sun ÷ SAt)
Hd1 First weekly holiday
(Sun ÷ nu) Set the first day of the week which follows the holiday
times.
Hd2 Second weekly holiday
(Sun ÷ nu) Set the second day of the week which follows the
holiday times.
N.B. Hd1,Hd2
can be set also as
“nu”
value (Not Used).
TO SET ENERGY SAVING TIMES (ONLY FOR MODELS WITH RTC)
ILE
Energy Saving cycle start during workdays
: (0 ÷ 23h 50 min.) During the Energy Saving
cycle the set point is increased by the value in HES so that the operation set point is SET +
HES.
dLE Energy Saving cycle length during workdays
: (0 ÷ 24h 00 min.) Sets the duration of the
Energy Saving cycle on workdays.
ISE
Energy Saving cycle start on holidays
. (0 ÷ 23h 50 min.)
dSE Energy Saving cycle length on holidays
(0 ÷ 24h 00 min.)
TO SET DEFROST TIMES (ONLY FOR MODELS WITH RTC)
Ld1÷Ld6 Workday defrost start
(0 ÷ 23h 50 min.) These parameters set the beginning of the 6
programmable defrost cycles during workdays. Ex. When
Ld2
= 12.4 the second defrost starts
at 12.40 during workdays.
Sd1÷Sd6 Holiday defrost start
(0 ÷ 23h 50 min.) These parameters set the beginning of the 6
programmable defrost cycles on holidays. Ex. When
Sd2
= 3.4 the second defrost starts at 3.40
on holidays.
N.B. :To disable a defrost cycle set it to “nu”(not used).
Ex.
If
Ld6
=nu
;
the sixth defrost
cycle is disabled
OTHER
Adr Serial address
(1÷244): Identifies the instrument address when connected to a ModBUS
compatible monitoring system.
PbC Type of probe:
it allows to set the kind of probe used by the instrument:
PbC
= PBC probe,
ntc
=
NTC probe.
onF on/off key enabling: nu =
disabled;
oFF =
enabled;
ES = not set it
.
dP1 Thermostat probe display
dP2 Evaporator probe display
dP3 Third probe display
-
optional
.
dP4 Fourth probe display
.
rSE Real set point:
it shows the set point used during the energy saving cycle or during the
continuous cycle.
rEL Software release
for internal use
.
Ptb Parameter table code:
readable only
.
8.
DIGITAL INPUTS
The first digital input 13-14 is enabled with P3P = n.
With P3P = n and i1F = i2F the second digital input is disabled
The free voltage digital inputs are programmable by the “
i1F
” and i2F parameters.
8.1
GENERIC ALARM (i1F or i2F = EAL)
As soon as the digital input is activated the unit will wait for “
did
” time delay before signalling the
“
EAL
” alarm message. The outputs status don’t change. The alarm stops just after the digital input is
de-activated.