background image

SPECIFICATIONS

2/16

Cal. V116A

Cal.V116A is ladie's 2 hands analogue watch employing a new solar panel (3 cell unit), but the 
basic movement structure of Cal.V116A is smilar to the previous Cal.V11 Series watches, and the 
knowledge and technique you have gained in handling the previous Cal.V11 Series watches will 
come in handy when you repair Cal.V116A.

 

FEATURES 

Cal. V116A

l

  Guideline of charging time

This is the ladies' analogue watch  powered by light energy.  The battery used in this watch 
is a rechargeable battery, which is different from ordinary silver oxide batteries.  Unlike other 
disposable batteries such as dry-cell batteries or button cells, this rechargeable battery can be 
used over and over again by repeating the cycles of discharging and recharging.

The capacity or recharging efficiency of the rechargeable battery may gradually deteriorate for 
various reasons such as long-term use or usage  conditions.  Worn or contaminated mechanical 
parts or degraded oils may also shorten recharging cycles.  If the efficiency of the rechargeable 
battery decreases, it is necessary to have the watch repaired.

Environment/

Light source

Illumination (lux)

Time required for 

full charge

Time required for 

steady operation

Time to charge 1 

day of power

Office, overhead/

Fluorescent light

700

-

60 hours 

180 minutes

30W 20 cm/

Fluorescent light

3,000

180 hours

10 hours 

35 minutes

30W 3 cm/

Fluorescent light

10,000

60 hours

4 hours

12 minutes

Cloudy weather/

Sunlight

10,000

60 hours

4 hours

12 minutes

Fine weather/

Sunlight

100,000

10 hours

0.5 hours

2 minutes

The above table provides only a general guideline.

It is recommended that the watch be charged for as long as the charging time according to the 
column "Time required for steady operation" in this table in order to assure the stable movement 
of the watch.

l

  Caution for charging

When charging the watch, do not place it too close to a photo flash light, spotlight, incandescent 
light or other light sources as the watch temperature will become extremely high, causing 
damage to the parts inside the watch.

When exposing the watch to sunlight to charge it, do not leave it on the dashboard of a car, etc. 
for a long time, as the watch temperature becomes extremely high. While charging the watch, 
make sure the watch temperature does not exceed 50 ºC.

TG V116A.indd   2

11/08/01   9:55

Summary of Contents for V116A

















Reviews: