background image

PARTS  CATALOGUE / TECHNICAL GUIDE

Cal. 8T63A 

[SPECIFICATIONS]

Cal. No.

Item

Interval of hands movement

Driving system

Additional function

Loss/gain

Regulation system

Gate time for rate measurement

 Power 

 

supply

Battery No.

Battery voltage

Battery life

Number of jewels

1/19

 Crown 

 

operation

Normal position

1st click position

2nd click position

Current consumption

Coil resistance

1 second

0 jewel

Stepping motor, 2 pieces

•   Stopwatch function

  60-minute stopwatch in one second increments.

•   Second hand stop function

•  Energy depletion forewarning function (The second hand moves at 

two-second interals.)

4002054 (COIL BLOCK A)

1.45 - 1.65 K

Ω

Use 10-second gate.

SEIKO SR936SW

Nil

1.55 V

Approx. 3 years

8T63A

 

•   3 hands (hour, minute, and 

small second hand)

•   24-hour indicator 

•   Date indicator

4002055 (COIL BLOCK B) 

1.65 - 1.85 K

Ω

Free

Date setting(clockwise)

Time setting, hand position adjustment / resetting the circuit 

  Monthly rate: Less than 15 seconds (worn on the wrist at the temperature 

between 5 and 35)

•   Diameter

  Outside: Ø 30.8 mm   

Casing: Ø 29.0 mm

•   Height:  5.1 mm 

 

Movement: Less than 2.70 μA

Circuit block: Less than 0.70 μA

Summary of Contents for 8T63A




















Reviews: