Seiko 6N76A Technical Manual Download Page 13

Page: 13 / 18

TECHNICAL GUIDE

Cal. 6N76A

13/18

●

How to set the FIRST DATE INDICATOR and the SECOND DATE INDICATOR

1) Calendar at 6 o’clock position

①

First position at random

②

First date indicator position

setting: Pull out the crown to
first click and turn the crown to
set day 3 to 1h position and day
5 to 6h position.

③

Second date indicator position

s e t t i n g : R o t a t e i t i n t h e
clockwise direction by touching
on its surface with finger until
the two holes overlap.

SECOND
DATE
INDICATOR

2) Calendar at 12 o’clock position

①

First position at random

②

First date indicator position

setting: Pull out the crown to
first click and turn the crown to
set day 3 to 7h position and day
5 to 12h position.

③

Second date indicator position

s e t t i n g : R o t a t e i t i n t h e
clockwise direction by touching
on its surface with finger until
the two holes overlap.

12h

fIRST AND SECOND
DATE INDICATOR
holes overlap

②

Second date indicator may only be
rotated in the clockwise direction.
If rotated counterclockwise, it may
cause malfuntion.

Notes:

①

Positions to take hold of the movement

NG (12h)

Ng (6h)

NG (3h)

NG (9h)

SECOND
DATE
INDICATOR

FIRST
DATE
INDICATOR

Summary of Contents for 6N76A



















Search results

Summary of Contents for 6N76A

Reviews:

Related manuals for 6N76A

Brands by name

Popular brands

Seiko 6N76A, Technical Manual

Search results

Summary of Contents for 6N76A

Reviews:

Related manuals for 6N76A

Brands by name

Popular brands