Seenergy SVR-116 Plus Quick Installation Manual Download

Page: 9 / 22

Quick Installation Guide

English

SEEnergy

“Plus”

Series

Network Video Recorder

LEDs Definition

HDD x 2

Green

Solid green when the hard disk is mounted and

being accessed

Red

Solid red for disk fail

Amber

Solid amber when recording is in process.

Blinking when recycling

Network

Amber

Solid amber for activity on a 1G bps network.

Green

Solid green for activity on a 10/100 Mbps

network.

Status

Amber

Blinking during firmware upgrade

Green

Shows solid green for normal operation.

Blinking green when firmware upgrade is done

Red

Flashes red for failed firmware upgrade.

Power

Green

Normal operation

Red

System off (power adapter remains plugged in)

Amber

Blinking amber indicating device is initializing

Alarm

Red

Blinking when an alarm occurs

None

When alarm is reset

Camera LEDs

Green Solid green, live connected with no event or

recording activity

Amber Blinking amber, manual or event recording is

being performed

Amber Solid amber, schedule or continuous

recording is being performed

Red

Recording is set but no video from camera

Summary of Contents for SVR-116 Plus























Search results

Summary of Contents for SVR-116 Plus

Reviews:

Related manuals for SVR-116 Plus

Brands by name

Popular brands

Seenergy SVR-116 Plus, Quick Installation Manual

Search results

Summary of Contents for SVR-116 Plus

Reviews:

Related manuals for SVR-116 Plus

Brands by name

Popular brands