SEDONA Sedona Island Assembly Instructions Manual Download Page 10

10

  

|

 

 

SEDONA ISlAND ASSEmbly INStructIONS

SEDONA ISLAND ASSEMBLY INSTRUCTIONS

We recommend a qualified, trained gas service technician 
perform all pipe fitting and gas leak test procedures prior to 
installing the refrigerator. Once installed there will be limited 
access to the gas piping. Before installing the side burner, 
familiarize yourself with the illustration on the next page.

Wrap the side burner manifold threads with Teflon tape, 
see Fig. 1 on page 11. Remove the 1/2” FIP fitting from 
the flexible hose and install it on the side burner manifold. 
Attach the stainless steel flexible hose to the 1/2” FIP fitting 
at the end of the side burner manifold.

Clear plastic replacement extension tubes are provided 
in the Open Me First box to drain spills and drain water 
from the side burner. Set the side burner in place in the 
counter top cutout. Be sure to keep the side burner wiring 
accessible to attach to the grill once it is installed. Route the 
tubes through the holes in the rear center of the island base 
for drainage out of the island.

On the bottom of the side burner locate the center Philips 
head screw on each side of the burner base. Remove the 
screw and install the side burner mounting bracket with it 
(Part No. 13, note weld nut position) flange up, as shown to 
the right. Screw the side burner mounting screw (Part No. 4) 
into the weld nut, and install the side burner mounting hex-
nut (Part No. 3) on the screw. Tighten the screw up to the 
side burner bracket frame to secure the side burner in place. 
Use the hex nut to lock the screw into position.

Step 9

Locate and remove the plug from the 1/2” Tee fitting in the 
grill manifold to facilitate the side burner connection (see 
the drawing on the next page).

With the help of an assistant set the grill in place. Make 
sure to align the grill evenly and be sure it is fully supported 
on the mounting flanges. Before sliding the grill back 
completely, reach behind the grill and attach the electrical 
wiring from the side burner using the attached Molex 
connectors (See page 13).

Step 10

Install the Grill

Install the Side Burner

Summary of Contents for Sedona Island





















Reviews: