background image

ST-IP2PTZ QUICK START GUIDE

 

Safety Instruction 

These instructions are intended to ensure that user can use the product correctly to 

avoid danger or property loss. 
The precaution measure is divided into 

Warnings

 and 

Cautions

Warnings: 

Neglecting any of the warnings may cause serious injury or death. 

Cautions:

 Neglecting any of the cautions may cause injury or equipment damage. 

Warnings

All the electronic operations should be in strict compliance with the electrical safety

regulations, fire prevention regulations and other related regulations in your local

region.

Please use the power adapter that is originally included. The power adapter standard

is 24VAC

10%, 12VDC

10% or 48VDC (PoE) (depending on models). The power

consumption cannot be less than the required value.

Do not connect several devices to one power adapter as adapter overload may cause 

over-heating or a fire hazard.

Please make sure that the power has been disconnected before you wire, install or

dismantle the speed dome.

When the product is installed on a wall or ceiling, the device shall be firmly fixed.

If smoke, odors or noise rise from the device, turn off the power at once and unplug 

the power cable, and then please contact technical support.

If the product does not work properly, please contact your dealer or technical support.

Never attempt to disassemble the speed dome yourself. (Securitytronix shall not

assume any responsibility for problems caused by unauthorized repair or

maintenance.)

Cautions

Do not drop the dome or subject it to physical shock, and do not expose it to high 

electromagnetic radiation. Avoid equipment installation on vibrating surface or places 

subject to shock (ignoring this can cause equipment damage).

Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire 

or electrical shock may occur. The operating temperature should be -22°F ~ 149°F.

The dome cover for indoor use shall be kept from rain and moisture.

Warnings

 Follow these safeguards 

to prevent serious injury or death. 

Cautions 

Follow these precautions 

to prevent potential injury or 

material damage. 

Summary of Contents for ST-IP2PTZ
















Reviews: