background image

v1.2  8/11/11 

5.  TROUBLESHOOTING 

a.  No  picture  after  applying  power  –  (i)  check  all  plugs  and  cables  are  securely 

connected  to  the  proper  connectors;  (ii)  ensure  your  power  supply  is  providing  the 
correct voltage and current. 

b.  The picture has ripples – (i) check to see if the power supply is experiencing AC ripple, 

if  so  a  filter  may  be  required;  (ii)  determine  if  the  monitor  is  faulty;  (iii)  determine  if 
other  peripheral  equipment  is  causing  ripple  and  if  so  make  the  necessary 
adjustments. 

c.  The picture background continuously changes color – a fluorescent lamp’s magnetic 

field  may  cause  color  roll,  therefore,  reduce  the  number  of  fluorescent  lamps  or 
increase the distance between the camera and the lamps. 

d.  The picture appears smeared – (i) the power supply voltage level may be unstable, 

therefore,  try  another  power  supply;  (ii)  ensure  the  cables  are  correctly  connected 
and/or the cables are of the correct impedance. 

e.  Other interference may require a Securitytronix ground loop isolation filter. 
f.  Additional troubleshooting assistance can be found on-line at 

www.securitytronix.com

 

in addition to support from Securitytronix sales engineers at 1-610-429-1511. 

 

 

Disclaimer:  Consult  all  regulatory  laws  regarding  hidden  &  covert  video  and  audio 
recording.  It is solely the buyer’s responsibility, not the seller, to ascertain and obey all 
applicable local, state, and federal laws regarding the possession and use of any item 
offered  by  Securitytronix.   By  placing  an  order,  the  buyer  represents  that  all  products 
purchased will be used in a lawful manner and that he/she is of legal age.

  

 

Summary of Contents for ST-CVTSD420-WSD-W






Reviews: