Secure Home SH-9910AU Installation And Operating Instructions Manual Download Page 4

4

201115-01

UP

FINAL ASSEMBLY

1.  Double check all wiring connections.

2.  Verify  the  rubber  gasket  is  properly  seated 

around the edge of the canopy extension (see 

Figure 6).

3.  Align the center hole on the fixture canopy 

with the center hole on the canopy extension 

and attach using the mounting bolt removed 

in step 1 of Installation (see Figure 6).

 

IMPORTANT:

• If wall mounted, make sure the fixture is 

mounted with the sensor below the lamp 

heads.

• If  eave  mounted,  mount  the  fixture  with 

sensor facing away from the house wall (see 

Eave Installation Information for important 

sensor orientation information).

4.  Push the rubber plug firmly into place (see 

Figure 7).

5.  Caulk around top half of canopy extension 

with silicone weather sealant (see Figure 7).

Terminal Block

From Fixture

From AC Source

WIRING

1.  Connect the house wires to the terminal block 

according to diagram (see Figure 4). Make 

sure all screws on terminal block are tightened 

securely.

2.  Remove the strain relief cover and place the house 

wires across the strain relief (see Figure 5).

3.  Replace  the  strain  relief  cover  and  tighten 

securely. 

Note:

 Be careful not to overtighten 

and damage the wiring.

 WARNING: Turn power off at circuit 

breaker or fuse. Place tape over circuit 

breaker switch and verify power is off at 

the fixture.

Green/Yellow

Green/Yellow

Blue

Blue or Black

Brown

Red or Brown

Figure 4

UP

Terminal Block

House Wiring

Screw

Strain Relief 

Cover

Figure 5

Figure 6

Mounting 

Bolt

Rubber Gasket

Fixture Canopy 

(Lamp 

heads and sensor not 

shown for clarity)

Summary of Contents for SH-9910AU









Reviews: