background image

FEATURES

• Energy efficient LED light source.

• Automatically comes on when motion is de-

tected.

• Automatically turns light off.

• Photocell keeps the light off during daylight 

hours.

• LED  indicates  motion  was  sensed  (day  or 

night).

UNPACKING

Be sure to remove all contents from packaging 

and verify all items are present before assembling 

this light fixture. This package includes the fol-

lowing items:

• LED Security Light

• Canopy Extension with Rubber Gasket

• Rubber Plug

• Mounting Bolt

• Owner’s Manual

REQUIREMENTS

• The light control requires 230 volts AC.

• If you want to use Manual Mode, the control 

must be wired through a switch.

• It is illegal for persons other than a licensed 

electrician or person authorized by legislation 

to work on fixed wiring or other electrical 

installations.

Before installation, record the model num-

ber listed inside the fixture. Attach receipt 

in case of possible warranty issues.
Model Number:

© 2011 The Chamberlain Group, Inc 

201115-01A

Installation and Operating Instructions

Motion Sensing

Light Control

Model: SH-9910AU

Security Light*

®

TM

*Note:

 Illustrations are for reference only and may 

be different from actual product

Summary of Contents for SH-9910AU









Reviews: