Page 9
Short programming manual - basic information
Intruder alarm system
|
FZoneVerifTime
}
15 seconds
|
Immid.EntryAla
}
No
Implemented on detection of smoke or fire for verification. When smoke or fire zone is violated, the system will
reset these detectors, then wait for detectors to settle. If a subsequent detection occurs in the same zone within
the time that is programmed in
Fire Verification Time
, the system will emit a fire alarm.
Event reports from entry zones to the CMS are delayed for 30 seconds after they are detected. Select
Yes
if the
event report should be sent immediately.
Each installation typically accommodates unique user PIN codes of up to 4 digits. The
Edit Users
menu provides access to submenus and
their related parameters that enable you to maintain
u
ser PIN codes in the system. The first user
’s
PIN code is used by the system’s owner
or chief user. This user has access to all the menus (except
Service mode
) and it can't be disabled.
Main menu
}
Settings
}
Users
}
Edit Users
USER PROGRAMMING
This options allows to restore current user PIN to default.
Factory
default user PIN depends on user
’s
number in
the system
:
U01 default PIN - 0001, U02 default PIN - 0002, U31 default PIN - 0031.
T
his menu entry is used to assign the remote control (RCU) or proximity tag to the system user.
T
o assign the
RCU or tag
-
choose the corresponding menu and press
the
[ENT]
key t
o program:
HC3S - s
imultaneosly
hold down
all
buttons.
LT5 - s
imultaneosly
hold down the buttons
[A]
and
[D]
.
Proximity tag - put the tag on sensitive area of the proximity reader.
Removing of the control unit can be done in the same menu.
Message
Done
should appear on keypad’s LCD
when
all
control unit
s
are removed from the user.
It is recommended to give a
n appropriate
name to a user. The system will use it
to send SMS or
for display
on
keypad's LCD
screen
.
All Users that have
status
mode
Enabled
can control system or its partitions.
The
Partitions
menu enables you to assign the partition(s) in which
the
user (except for the 1st system user) will
operate.
Used to allow users to control the system during predefined time periods.
Note:
if the timer is not assigned,
the
user will be able
to
control the system without time limitation.
All system users have all rights assigned by default. However, it is possible to change them. The user has
access to the following:
Arm
;
Disarm
;
Clear alarm
;
Abort arming
;
Bypass zones
;
Edit settings
;
View Event log
;
Test fire zones
;
Send test report
;
Control PGM outputs
;
Edit system users
;
Right to enable service
;
U01
|
Name
}
User 01
U01
|
Status
}
Enabled
U01
|
Partitions
}
+Partition 01
U01
|
Timers
}
-Timer 01
U01
|
Reset PIN
}
No
U01
|
Controls
}
New RCU
U01
|
Rights
}
+Arm
T01
|
Name
}
Timer 01
T01
|
TMR On Time
}
T01
|
TMR Off Time
}
23:00 Enabled
00:00 Disabled
T01
|
Schedule
}
-----++
System timers consist of an ON time and an OFF time, and selected days of the week in which they are active. There are up to 16 timers
(depends on control panel type) that can be used to make auto arming schedule or to control various devices, such as lights or appliances.
Main menu
}
Settings
}
Timers
SYSTEM TIMERS PROGRAMMING
It is recommended to give an appropriate name to a timer.
Timer is in use when it is enabled. Use the 24-hour clock to program the timer On/Off time .
Select the days when the system timer will activate. Use
the
[ENT] key
to enter to the menu, then press [#]
to
assign day to the timer. Save changes by pressing the [ENT]
key.
SECURITY SETTINGS
Service Mode
}
System Setup
}
Security Settings
This setting allows to enable or to disable access to the special user menu, where installer with his PIN can
restore 1st user’s PIN to default and the 1st user with his PIN can restore all enabled user PINs to default.
This feature is
intended for
situations where the
us
er
is forced to disarm or arm the system under
a
threat.
This setting enables or disables this feature. Duress code is individual for every system user. Duress code =
X1, X2,
X3,
X4
w
hen
X
4 = X4 + 1 (X1, X2, X3, X4 are digits). Example: user PIN is 123
4
, duress code
will
be 123
5
.
|
PIN Resetting
}
Disabled
|
Duress
}
Disabled
System with
KM2
0B
keypads
