Seav 93070000, Manual

Page: 10 / 61

10 Rev. 3.0 13/06/16
and hold the SET key to raise the shutter; release the key when
the blind is at the required point; the motor time is stored at the
same time and the LED T.MOT key stays ON.
If you are using an automation system with a stop limit, we rec-
ommend that you store a time that exceeds the shutter’s stop
limit by a few seconds.
If you require unlimited motor time, follow the same program-
ming instructions holding down the SET key for less than two
seconds; the LED T.MOT stays ON and the unlimited time is
set. The operation may be repeated if a mistake is made during
programming.
16) WIND SPEED (Programming Wind Threshold)
Displaying the programmed Wind threshold
The wind safety threshold selection is displayed as follows: use
the SEL key to navigate to the WIND SPEED LED; the LED
then indicates the wind safety threshold, whereby every double-
flash of the WIND SPEED LED indicates an increment of 5
km/h ( e.g. the WIND SPEED LED flashes 5 times = 25 km/h) .
Setting the wind safety threshold between 5 and 40 Km/h
The control unit comes with a wind safety threshold already set
at 25 km/h (WIND SPEED LED OFF).
The wind safety threshold is programmed as follows: use the
SEL key to navigate to the WIND SPEED LED, then press the
SET key to start programming; the WIND SPEED LED will then
begin to double-flash (each double flash of the WIND SPEED
LED corresponds to an increment of 5 km/h). Press the SET
key once the required threshold has been reached. The select-
ed threshold is stored and the WIND SPEED LED stays ON
( e.g. the WIND SPEED LED flashes 5 times = 25 km/h) .
The operation may be repeated if a mistake is made during
programming.
17) SUN SENSOR (Sun Sensor ON/OFF)
Enabling the sun sensor
The control unit comes with a Sun Sensor disabled (SUN
SENSOR LED OFF).
The Sun Sensor can be enabled as follows: use the SEL key to
navigate to the SUN SENSOR LED then press the SET key for
a second. The SUN SENSOR LED stays ON at the same time.
The Sun Sensor is now enabled. Simply repeat this procedure
to disable the Sun Sensor.
Enabling the Sun Sensor with 3-key radio control (BeFree
x3 - X6):
The Sun Sensor can be enabled as follows: press and hold for
five seconds the (+) key of a previously stored radio control.
The control unit executes an up/down movement for 1 second
to confirm the Sun Sensor is enabled and the SUN SENSOR
LED stays ON. Simply repeat this procedure to disabled the
Sun Sensor, but pressing and holding the (-) key for 5 seconds
(instead of the (+) one).
18) RAIN SENSOR (Rain sensor ON/OFF)
Disabling the rain sensor
The control unit comes with a Rain Sensor enabled (RAIN
SENSOR LED ON).
The Rain Sensor can be disabled as follows: use the SEL key
to navigate to the RAIN SENSOR LED, then press and hold the
SET key for a second. The RAIN SENSOR LED switches off
and the Rain Sensor is disabled. Simply repeat this procedure
to enable the Rain Sensor.
EXTENDED MENU
The manufacturer provides the control unit with only the option
of selecting the functions of the main menu.
If you wish to enable the functions of the extended menu, pro-
ceed as follows: press and hold the SET key for 5 seconds; the
SUN and RAIN LEDs will flash alternately; you then have 30
seconds within which to select the functions of the extended
menu using the SEL and SET keys; after another 30 seconds
the control unit returns to the main menu.
---------------------- EXTENDED MENU -----------------
LED reference LED off LED on
A) CODE M1 Step by step Manual/ P-P S. Aut.
B) CODE M2 Step by step Venetian blind / P-P S. Aut.
C) CODE M3 Simultaneous start-up 5 sec sequential start-up
D) CODE M4 Start-up delay time = OFF Start-up delay time= Pgm
E) CODE SENS. Line Sensor test = OFF Line Sensor test = ON
F) T. MOT. Aut shutdown = OFF Aut shutdown = ON
G) WIND SPEED Safety up movmt = OFF Safety up movmt = ON
H) SUN SENSOR RAIN inversion = OFF RAIN inversion = ON
I) RAIN SENSOR SUN inversion = OFF SUN inversion = ON
L) SUN ON/OFF intermittent
M) RAIN ON/OFF intermittent
A – B ) CODE M1 – M2
(4 different selectable operating logics):
Step by step:
Step by step operation is possible using the radio control and
pushbutton control. The first impulsive control raises the blind
for the motor time. The second impulsive control lowers the
blind. If an impulsive command is sent before the motor stops
running, the control unit stops the blind; another impulsive
command re-activates the blind in the opposite direction.
Manual:
Manual operation is possible using the radio control and
pushbutton control. The control needs to be constantly enabled
to move the blind. Releasing the key will always stop operation.
Venetian blind operation:
The Venetian blind mode involves manual operation for the first
2 seconds using both the radio control and pushbutton control;
this allows you to turn the slats of the Venetian blind ever so
slightly to let more or less light into the room as required. If the
commands are more than 2 seconds, the blind is raised or low-
ered depending on the key pressed, until the motor stops run-
ning.
Step by step + Automatic sensors:
The control unit enables step by step operation as above, as
well as automatic management of the Wind and Rain sensors.
Ten minutes after the wind or rain that activated one of the two
sensors, the control unit lowers the blind.
Selection mode:
The control unit allows you to select 4 different operating logics:
step by step, manual, Venetian blind and step by step + auto-
matic sensors.
The control unit is provided with step by step operation already
enabled (M1 CODE LED AND M2 CODE LED disabled). If you
wish to enable the other operating mode, proceed as follows:
enable the extended menu (the SUN and RAIN LEDs will flash
to confirm this); use the SEL key to navigate to the M1 CODE
LED, then press the SET key to enable the Manual function;
use the SEL key to navigate to the M2 CODE LED, then press
the SET key to enable the Venetian blind function, or use the
SEL key to navigate to the M1 CODE LED and M2 CODE LED,
then press the SET key to enable the Step by step + Automatic
Sensors function.
C) CODE M3
(Simultaneous or sequential start-up):
The control unit is provided with simultaneous start-up of the 4
motors already enabled. If you wish to have a 5-second interval
in between the start-up of each motor, proceed as follows: ena-
ble the extended menu (the SUN and RAIN LEDs flash to con-
firm this), use the SEL key to navigate to the CODE M3 LED
and then press the SET key; at the same time the CODE M3
LED switches on permanently and programming is ended.
Simply repeat this procedure to restore the previous configura-
tion.