Seat Comfort Systems 6 Motor Massage System
Seat massagers should never
be installed into foam where an
occupant detection sensor is
present on the surface of the
foam cushion.
The installer is liable for any
damage due to improper fitting
or not following these
instructions.
Seat massage motors are to be
installed on the seat foam only
.
Installation has to be
performed by qualified
personal only. Improper
installation will void the
warranty and may cause
physical damage to equipment
or people.
Dismantling the seat
Disconnect and isolate the
battery negative (ground) cable
and wait five minutes for the
system to discharge.
Dismantle the seat that will be
fitted with the heating pads. In
most cases striping the seat
cover is easier with the seat out
of the car.
Remove all seat covers in the
area you are planning to fit the
massage system and wire
harness.
Removing The Seat Cover
Separate cushion and back
from each other by removing
the covers and unscrewing the
connecting screws. It is
advised to put the seat on a
dedicated worktable for the
following steps.
Remove the cover of both seat
and back. To do so remove and
dispose all upholstery clips.
Unhook all other connections
using a suitable screwdriver.
Make sure that there are no
loose metal parts left on the
foam like hog rings.
Massage Motor Placement
Lay the massage motors on the
seat
and
determine
the
placement of the motors.
Suggested
placement
are
locations that will be under the
muscle structure of the user.
Avoid the shoulder blade area
and
the
belt
line
area.
Placement locations are “lower
back” (above or below belt
line), middle back and upper
back (below/between shoulder
blades).
Using a marker, trace out the
motor outline, making sure the
motors
locations
are
symmetrical.
Cutting Foam Pockets
Using a blade or knife, cut the
pocket for the massage motor.
Cut on the inside of the
marked line, 1” deep. Grab the
foam at the top cut and gently
pull back while cutting the
foam at the 1” deep base. Try
to cut evenly so the pocket is
flat..
Motor Installation
Cut a slit on the top of the
pocket and then slide the
massage motor in from the
back of the foam back. Make
sure the motor wire colors are
the same. Using spray glue,
spray into the foam cavity and
then place the motor in the
cavity. Gently pull the wire
from the back of the seat back
and secure the motor into the
cavity.
Foam
motor
glue
Wire harness and switch
While running the wire harness
you have to pay attention, that
the wire cannot be cut,
crimped or damaged in any
other way. The wire harness is
to be attached to the seat frame
securely.
Plug the open connector of the
motor harness to the controller
and attach the controller to the
seat frame.
Run the switch wire harness to
the center console or side seat
shield. Drill a 25mm hole in
the panel, Pull the connecting
wire through and then plug in
the switch and push the switch
into the panel (please push on
the outer bezel of the switch).
Electrical connection and
function test
Black to Ground
Red to accessory power
White to accessory power
*Connect to a switched source
capable of driving 5 Amps
continuous current.
Power Connection
Connect the red wire to
fused 12 volt power.
Connect the black wire to
ground.
Connect the white wire to
accessory power. If you
are not using accessory
power, join the white and
red wire together. (The
white wire is a signal wire
input).
Route the wire harness
from the seat along the door
sill plate to the fuse box as
shown below.
Massage Operation
M
– Manual Mode
Press once for low intensity
Press again for increased
intensity
Press third time for maximum
intensity
Press to turn off.
A
– Automatic Mode
There are 8 rhythm modes
that are cycled.
Press once for low intensity
Press again for increased
intensity
Press third time for maximum
intensity
Press to turn off.
Upper
Middle
Lower
A
M
