manualshive.com logo in svg

Sears CRAFTSMAN 944.604060, Owner'S Manual

Share
Download
Sears CRAFTSMAN 944.604060 Owner'S Manual Download Page 35

35

REPAIR PARTS

TRACTOR - - MODEL NUMBER 944.604060

CHASSIS AND ENCLOSURES

1         180375           Rail, Frame RH
2         175282           Drawbar, Gt
4         73680700       Nut Crown Lock 7/16-14
5         187934X428  Dash
6         157882           Dash Asm., Lower
7         17720408       Screw, Thd Cut  1/4-20 x 1/2
8         184668           Support, Battery
14       175260X613  Hood Asm., Pnt
16       121794X        Cover, Access
17       17000612       Screw, 3/8-16 x 3/4
18       174515X613  Grille 
19       19131312       Washer  13/32 x 13/16 x 12 Ga.
20       STD523710   Bolt, Fin Hex  3/8-16 x 1
21       STD541437   Nut, Crownlock  3/8-16 unc
24       179717X613  Footrest, RH
28       179716X613  Footrest, LH
30       145051X014  Saddle
31       161419           Bracket, Supt 1-pc VGT Steering
32       161327           Bracket, Pivot Chassis LH
33       161326           Bracket, Pivot Chassis RH
35       19111116       Washer 11/32 x 11/16 x 16 Ga.
36       17060512       Screw 5/16-18 x 3/4
37       179772X613  Fender, Pnt. 
39       175278           Bracket, Axle Front
43       136939           Bracket, Spnsn Front Lh
44       136940           Bracket, Spnsn Front Rh
45       176018           Bracket Asm., Susp Chassis Rh
50       175476           Bracket, Chassis Front
56       176016           Bracket Asm., Susp Chassis Lh
58       183569           Bracket Asm., Fender

KEY    PART
NO.     NO.                DESCRIPTION

NOTE:

 

 

All component dimensions given in U.S. inches

             1 inch = 25.4 mm

KEY    PART
NO.     NO.                DESCRIPTION

60       17000616       Screw
63       19131614       Washer
66       17490608       Screw
67       156973           Guide Belt
68       17490508       Screw, Thd  5/16-18 x 1/2
70       177679           Belt Keeper Ground Drive
85       144911           Bracket Support Transaxle
86       74780716       Bolt, Fin Hex  7/16-14 unc x 1
88       STD551143   Washer
91       180374           Rail, Frame Lh
106     17580520       Screw
122     161464           Screw Hex Wshd 8-18 x 7/8
130     171875           Screw HWHD Hi-Lo #13-16 x 3/4
138     179125X428  Cupholder YTGT
139     171873           Bolt Shoulder 5/16-18 TT
142     161897           Bracket Dash RH
144     161900           Bracket Dash LH
148     164655           Extrusion Bumper
150     175352           Duct Heat Hood 
152     177956           Shield Browning
153     179761           Lens Asm (Includes #157)
156     17000512       Screw 5/16-18 x 3/4
157     161840           Lens Bar Stealth
158     17670608       Screw Thdr 3/8-16 x 1/2
161     179612X428  Console Fuel Window
162     142432           Screw Hex Wsh Hi-Lo 1/4-1/2
165     183554           Bracket Support Tank
171     184672           Bushing Snap

Summary of Contents for CRAFTSMAN 944.604060

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands