background image

8

C. With finger pressure press seat firmly and squarely into cav-

ity. See Figure 10A. Polished face of seat faces inside of pump.
If seat will not locate properly, place cardboard washer over
polished face and use piece of 3/4” standard pipe for press-
ing purposes. See Figure 10B.

D. Dispose of cardboard washer and clean surface of seat.

E. Clean motor shaft.

F. Reassemble back half of pump to motor.

G. Apply detergent solution to inside diameter of rotating seal

member.

H. Slide rotating member on shaft until rubber drive ring hits

shaft shoulder.

NOTICE: BE SURE

you do not chip or scratch

seal face on shaft shoulder or seal will leak!

I. Screw impeller on shaft (clockwise) while holding shaft with

7/16” open end wrench on shaft flats. This will automatically
locate seal in place. See Figure 11.

J. Reposition capacitor and replace motor canopy.

K. Remount diffuser on seal plate.

Cleaning Impeller

1. Follow steps 1A through 1E under “Disassembly and Assembly

of Pump” on Page 7.

2. Remove diffuser and impeller from pump per instructions under

“Removing Motor for Service and Replacing Shaft Seal” on Page
7.

3. Clean impeller and reassemble impeller and diffuser per in-

structions under “Removing Motor for Service and Replacing
Shaft Seal” on pages 7 and 8.

Cleaning Shallow Well Jet

To remove debris from venturi or nozzle, proceed as follows:

1. Disassemble pump per instructions on Page 7.

2. Turn venturi counterclockwise and remove it. The nozzle is

now exposed. Remove it using a 5/8” hex socket wrench with
extension. Turn counterclockwise. If socket wrench is not avail-
able, insert an ice pick or similar pointed tool carefully into the
nozzle. This will dislodge debris.

3. Flush out the debris by running water through the nozzle in the

same direction as the dislodging tool was inserted.

4. Reinstall nozzle and venturi. Do not overtighten!

5. Reassemble pump per instructions on Page 7.

HELPFUL HINTS

How to Handle a Gaseous Well

In some areas well water contains gases which must be allowed to
escape before the water is used. This can be done as shown in
Figure 12.

A good way of delivering gas-free water is to suspend a pipe, closed
at the bottom and open at the top, surrounding the suction pipe.
Since the gases rise in the well casing, the water sucked down
through the pipe and into the suction pipe is free of gas. This type
of well must be vented to the outside of any enclosure.

Air Control in Flowing Wells

Flowing wells, or wells with little or no drawdown, could create a
special problem in air control in the operation of your water sys-
tem.

In such cases, install a Captive Air® Tank. It does not require any
air control.

Figure 12

Not

to

Scale

Pipe strap or
wire to hold
pipe sleeve

Pipe
sleeve

Pipe
cap

Tail
pipe

Foot
valve

2369 0396

Gases
rise to 
surface

SERVICE

477 0194

483 0194

478 0194

FIGURE 10A

FIGURE 10B

FIGURE 11

Summary of Contents for CRAFTSMAN 390.251482













Reviews: