manualshive.com logo in svg

Sealite SLC500, Installation & Service Manual

Share
Download
Sealite SLC500 Installation & Service Manual Download Page 30

Latest products and information available at www.sealite.com

30

SL-C500 & SL-C600 

Solar Marine Lanterns

Now that the lantern has been programmed to suit the project requirements, it’s important that the 

lantern is tested prior to installation, including flash code and intensity settings.  
To test the lantern:
•  Connect the SL-155 to a 12V power supply or battery 
•  For lanterns programmed to “Dusk to Dawn” operation setting, cover lantern with a dark cloth or 

jack in darkness for more than 1 minute. After this time the lantern will activate

•  Next, check that the lantern is flashing to the required flash code and intensity
•  If the settings are correct, disconnect from the 12V power supply or battery 
•  If the settings are incorrect, following the Programming Instructions of this manual to re-configure 

lantern characteristics, and then re-test prior to installation 

IMPORTANT:

 when lantern is being programmed using the Sealite PC Configuration Tool software, 

it is recommended that the operation setting is set to “Always On” for ease of testing/viewing new 

settings. Once the programming is complete, remember to change the operation mode back to your 

specific installation requirement (Sealite recommend “Dusk to Dawn” mode). 

Lantern Testing

Summary of Contents for SLC500













































Reviews:

No comments

Brands by name

Popular brands

Load more brands