air/hydraulic press
30 tonne floor type with foot pedal
model no:
yK309fah
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
9
Familiarise yourself with the applications, limitations and hazards of the press.
9
maintain the
press in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the press clean for best and safest performance.
9
locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure
there is adequate lighting.
9
ensure the workpiece is correctly secured before operating the press.
9
ensure that all fittings are tight before each use.
9
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
9
Keep hands and body clear of the table when operating the press.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Securely attach the press to a flat, firm, level surface capable of supporting the weight of press and any workpiece taking into account
clearance for workpieces.
9
When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the arbor plates in a safe location.
8
do not
operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
do not
use the press for a task it is not designed to perform.
8
do not
make any modifications to the press.
8
do not
exceed the rated capacity of the press.
8
do not
apply off-centre loads.
8
do not
allow the workpiece or the arbor plates to fall from the table.
8
do not
get the press wet or use in damp or wet locations or areas where there is condensation.
8
do not
operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not
climb upon the press.
8
do not
use the press to compress a spring or any other item that could disengage and cause a potential hazard including personal
injury.
8
do not
stand directly in front of a loaded press and never leave a loaded press unattended.
8
do not
allow untrained persons to operate the press.
warninG!
Always wear approved eye or face protection when operating the press. A full range of personal safety equipment is available
from your Sealey stockist.
warninG: do not
top up hydraulic unit with brake fluid, or any other fluid other than a good quality hydraulic oil (Sealey Part
number: HJo500mlS/HJo5lS) as this may cause serious damage to the hydraulic unit and will invalidate the warranty.
warninG!
Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard
be placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.
warninG!
The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
▲
danGer!
The press is top heavy. If it requires moving after assembly or for relocation, use suitable slings around the top
crossbeam, or lift direct with a forklift with the forks located under the top crossbeam.
do not
use a pallet truck.
2.
i
introduction
Steel frame construction with side mounted air motor powering hydraulic pump unit, foot pedal operated. Sliding hydraulic ram assembly
with lateral travel for off-centre pressing applications. Fitted with ram pressure gauge. Supplied with flat pressing plate/V-blocks.
3.
i
specification
model .......................................................................YK309FAH
Capacity .......................................................................30tonne
Ram stroke ....................................................................150mm
Ram diameter ..................................................................70mm
lateral ram travel ..........................................................200mm
Original Language Version
© Jack Sealey limited
Refer to
instruction
manual
Wear protective
gloves
Wear face
mask
Wear protective
clothing
Wear safety
footwear
Warning:
Crushing of
hands
YK309FAH Issue 2 (H, F) 30/11/18
