1.2.
GENERAL SAFETY
▲
DANGER! Unplug the welder from the mains power supply before performing maintenance or service.
9
Keep the welder and cables in good working order and condition. Take immediate action to repair or replace damaged parts.
9
Use genuine parts and accessories only. Unapproved parts may be dangerous and will invalidate the warranty.
9
Use an air hose to regularly blow out any dirt from the liner and keep the welder clean for best and safest performance.
9
Check and spray the gas cup and contact tip regularly with anti-spatter spray, available from your Sealey stockist.
9
Locate welder in a suitable work area. Ensure that the area has adequate ventilation as welding fumes can be harmful.
9
Keep work area clean, tidy and free from unrelated materials. Also ensure the working area has adequate lighting and that a fire
extinguisher is at hand.
WARNING! Use welding head shield to protect eyes and avoid exposing skin to ultraviolet rays given off by electric arc. Wear
safety welding gauntlets.
9
Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery and contain long hair.
9
Ensure the workpiece is correctly secured before welding.
9
Avoid unintentional contact with the workpiece. Accidental or uncontrolled use of the torch may be dangerous and will wear the nozzle.
9
Keep unauthorised persons away from the work area. Any persons working within the area must wear a protective head shield and gloves.
9
Operators must receive adequate training before using the welder.
9
Stand correctly keeping a good footing and balance, ensure the floor is not slippery and wear non-slip shoes.
8
DO NOT
operate the welder if it or the cables are damaged.
8
DO NOT
attempt to fit any unapproved torches or other components to the welder.
8
DO NOT
get welder wet or use in damp or wet locations or areas where there is condensation.
▲
DANGER! DO NOT weld near flammable solids, liquids or gases and DO NOT weld containers or pipes which have held
flammable materials. Avoid welding materials which have been cleaned with chlorinated solvents or welding near such solvents.
8
DO NOT
stand welder on a metal workbench, car bodywork or similar.
8
DO NOT
touch any live metal parts of the torch or electrode while the machine is switched on.
8
DO NOT
pull the welder by the cable, or the torch. Protect cables from sharp or abrasive items.
DO NOT
bend, strain or stand on
cables or leads. Protect from heat. Long lengths of slack must be gathered and neatly coiled.
DO NOT
place cables where they
endanger others.
8
DO NOT
touch the torch or workpiece immediately after welding as they will be very hot. Allow to cool.
8
DO NOT
operate welder while under the influence of drugs, alcohol or intoxicating medication, or if tired.
9
When not in use store the welder in a safe, dry, childproof area.
1.3.
GAS SAFETY
9
Store gas cylinders in a vertical position only and ensure the storage area is correctly secured.
8
DO NOT
store gas cylinders in areas where the temperature may exceed 50°C.
DO NOT
use direct heat on a cylinder. Always keep
gas cylinders cool.
8
DO NOT
attempt to repair or modify any part of a gas cylinder or valve and
DO NOT
puncture or damage a cylinder.
8
DO NOT
obscure or remove any official labels on a cylinder. Always check the gas identity before use. Avoid getting gas cylinders oily or
greasy.
8
DO NOT
lift a cylinder by the cap, guard or valve. Always keep caps and guards in place and close valve when not in use.
2. INTRODUCTION
Forced Air Cooling System allows high duty cycle. Professional contour grip, heat-proof non-live torch ensures no sparks until you
press the trigger. Proven wire feed system for trouble-free welding. Welds stainless and aluminium too.
IMPORTANT:
These instructions contain the information you require to prepare your machine for welding, together with a maintenance
and a troubleshooting section. The instructions are not intended to teach you how to weld. If you have no experience, we recommend that
you seek training from an expert source. MIG welding is relatively easy, but does require a steady hand and supervised practice on scrap
metal, as it is only with continued practice that you will achieve the desired results.
3.
sp
SPECIFICATION
Model No: .......................................................
Supermig140.V2
W
elding current: ..........................................................
30-140A
W
ire Capacity: ...............................................................
0.7-5kg
Duty Cycle: ................
100% @ 36A, 75% @ 41A, 20% @ 80A
Cooilng System: ....................................................... Forced Air
S
pot Welding Timer:
............................................................. No
Gas Type: ...................................
CO2, Argon, CO2/Argon Mix
Torch: .................................................................2m Non-Live
Supply: ...........................................................................
230V
Absorbed Power: ..........................................................
2.8kW
Case Size: ................................................................Compact
4. ASSEMBLY
4.1.
HANDLE
4.1.1.
Take the straight metal handle section and identify the end which has a rectangular hole in it’s rounded top surface. See ‘C’ in fig.1-A.
4.1.2.
Ensuring that this hole is uppermost, insert the handle into the opening in the front of the plastic handle until the catch ‘D’ engages in
the hole ‘C’ as shown in fig.1-B.
4.1.3.
WHEELS.
Referring to fig.2, attach a wheel (1) to axle (2) using a circlip (3) and insert a hub cap (4) into the centre of the wheel.
4.1.4.
Raise the welder from the ground by approximately 70mm and insert the axle fixing plates (5) through the slots in the rear platform as
shown below.
4.1.5.
Slide the axle (2) underneath the rear platform and through the holes in the axle fixing plates.
4.1.6.
Slide the other wheel (1) over the protruding axle (2) and fix in place using a circlip (3).
4.1.7.
Push the other hub cap (4) into the centre of the wheel.
4.1.8.
FOOT.
Attach the bent metal foot to the underside of the welder just back from the front panel using the two self tapping screws provided.
Original Language Version
© Jack Sealey Limited
fig.1
S
UPERMIG140.V2 Issue:1 08/07/22
