3.1.
Hold the torque wrench in your left hand (if right handed) so that the
required scale on the shaft, just above the hand grip - is uppermost and
visible.
3.2.
Turn the lock screw, in the end of the grip, counter-clockwise to unlock grip
(STW201.V2 has a locking plug in the end of the grip - pull ring to unlock).
3.3.
Turn grip to select torque setting as follows:
• Required setting - 56Nm
• Turn grip until top edge is level with the 50Nm line on the shaft scale
and the ‘zero’ on the grip graduation is aligned with the centre line of
the shaft scale.
• Rotate the grip further, clockwise, until the ‘6’ on the grip graduation is
aligned with the centre line to give a
setting of 50 + 6 = 56Nm.
Note: If using the alternative scale (lb.in, lb.ft or kg.m depending on
wrench) then each division of the grip graduation is equivalent to
the scale increment divided by the number of divisions. For
example (STW1011):
The alternative scale is in lb.ft.
Scale increments are 5.16lb.ft
There are 7 grip divisions.
Then each division is 5.16/7 = 0.74lb.ft
3.4.
Tighten the lock screw at the end of the handle to prevent accidental
alteration of the setting.
3.5.
When tightening the nut/bolt you will feel and hear the wrench
mechanism click when the set torque is reached. Immediately stop
applying force to the wrench to avoid over-tightening the nut/bolt.
The wrench will reset ready for the next application.
Note: If wrench is not used for some while, operate it a few times, at a
low setting, to ensure that all internal parts are coated in grease.
Ensure all workshop safety rules, regulations, and conditions are complied with when using the torque wrench.
Maintain the
wrench in good condition and replace any damaged or worn parts.
Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
The wrench is a precision tool,
DO NOT
abuse it.
DO NOT
drop or throw the wrench.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
WARNING! DO NOT
use the wrench if damaged or thought to be faulty (contact Service Agent).
DO NOT
use wrench unless you have been instructed in its use by a qualified person.
DO NOT
use any cleaner which might affect the high pressure grease with which the wrench is packed.
After use adjust to lowest torque setting (but not below),clean and store in a safe, dry, childproof location.
2.1. Introduction
These torque wrenches are precision tools and each is supplied with a calibration certificate. Torque setting is by means of a micrometer type adjuster and the drive
head has a reversible ratchet.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly maintained, give years of trouble free performance.
INSTRucTIoNS FoR:
TORQUE WRENCHES
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATIONS
3. OPERATION
4. RECAlIbRATION
5. CAlIbRATION CERTIFICATE
4.1
To ensure continued accuracy the wrench should be
recalibrated annually and after any impact or other misuse.
contact your Sealey dealer or a NAMAS accredited laboratory.
5.1
See over for the calibration certificate for this wrench.
IMPORTANT:
PlEASE READ THESE INSTRUCTIONS CAREFUllY. NOTE THE SAFE OPERATIONAl REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTlY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAIlURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAl INJURY AND WIll
INVAlIDATE THE WARRANTY. PlEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
STW101, STW1011, STW102, STW103,STW104,
STW200, STW201.V2, STW202, STW1012 (I)
Issue: 3 - 16/01/14
2.2. Specifications
Model No. . . . . . . . . .STW101 . . . .STW1011 . . .STW102 . . . .STW103 . . . STW104 . . . . STW200 . . . STW201.V2 . . . .STW202 . . .STW1012
Torque Range (Nm)
. .
5-25
. . . . . . .7-112 . . . . . .
40-210
. . . . .
70-420
. . . .
140-700
. . . . 10-110 . . . . . 30-210 . . . . . . . .
50-560
. . . .
2-24
Alternative Scale . . . .
44-221lb.in
. .
5-83lb.ft
. . . .
30-155lb.ft
. .
52-310lb.ft
. .
103-516lb.ft
. .
10-80lb.ft
. . .
20-150lb.ft
. . . . .
50-400lb.ft
.
1.47-17.7lb.ft
Drive (sq) . . . . . . . . . .
1/4”
. . . . . . . .
3/8”
. . . . . . . .
1/2”
. . . . . . . .
3/4”
. . . . . . .
3/4”
. . . . . . . .
3/8”
. . . . . . .
1/2”
. . . . . . . . . . .
3/4”
. . . . . . .
3/8”
Length (mm) . . . . . . . .
275
. . . . . . . .370 . . . . . . . .
460
. . . . . . . .
650
. . . . . . . 1070 . . . . . . .
405
. . . . . . .
490
. . . . . . . . . . .
675
. . . . . . .
275
MoDEL No's
STW101 STW1011 STW102 STW103 STW104 STW200 STW201.V2 STW202 STW1012
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
W e b
© Jack Sealey Limited
