NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
for a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
5. OPERATION
4.13. remove the lock nut from the bottom bracket of the
hopper as shown in figure 8.
4.14. attach a brace (3) to the bottom bracket of the hopper (1)
using the lock nut removed in 4.13 and hex bolt m6x16
(7) and lock nut m6 (9) as shown in figure 8. Do not fully
tighten the nuts and bolts at this stage.
4.15. attach the other end of the brace to the hitch tongue using
hex bolt m6x16 (7) and lock nut m6 (9) as shown in
figure 9. Do not fully tighten the nuts and bolts at this
stage.
4.16. repeat the procedure for the opposite side, again not fully
tightening the nuts and bolts.
4.17. adjust the position of the hitch tongue so that it is
perpendicular to the hopper and fully tighten all the
relevant nuts and bolts.
4.18. Place a flat washer Ø20 (11) onto the axle tube followed by
a spacer (12) and then another flat washer Ø20 (11), as
shown in figure 10.
4.19. attach the pneumatic wheel (4) with the valve facing
outwards. align the hole in the wheel hub with the hole in
the axle and secure using hex bolt m6x50 (8) and lock
nut m6 (9), as shown in figure 11. repeat the procedure
for the opposite side.
4.20. the spreader is now fully assembled and ready for use.
Original Language Version
5.1.
read the safety Instructions in section 1 before operating the
spreader.
5.2.
secure the spreader onto the prime mover using the towing
pin on the hitch tongue. secure the towing pin with the r-pin
provided. the spreader can be converted to use a ball hitch
by fitting a sealey Ø50mm towing Hitch, model no. tB36,
available from your sealey dealer.
5.3.
Load the product into the hopper, ensuring that it is evenly
distributed and the maximum capacity of the spreader is not
exceeded. When handling hazardous products it is important
to first read the safety data sheet and take necessary safety
precautions. a full range of personal safety equipment is
available from your sealey dealer.
5.4.
the towing speed will affect the rate of flow from the
spreader. It is advisable to operate the spreader at lower
speeds for a more effective flow of the product.
5.5.
the adjustable feed system is controlled by movement of the
handle on the hitch tongue. operate the spreader at the
desired speed and adjust the handle either forwards or
backwards until a satisfactory rate of flow is achieved. a
locking device is provided on the gauge to allow the optimum
flow required to be maintained.
5.6.
clean the spreader thoroughly after use, paying particular
attention to the area around the adjustable flow control
system and the agitator blade.
fig.8
fig.9
fig.10
fig.11
6. MAINTENANCE
6.1
after each use clean material out of hopper.
6.1.1 rinse/dry inside and outside of spreader after each use.
6.1.2 Before operating make sure that the tyres are inflated to the
correct pressure.
6.1.3 Periodically check all fastenings are tight.
6.1.4 annually clean and lightly lubricate parts.
6.1.5 touch up all scratched or worn painted metal surfaces.
6.1.6 to avoid damaging the spreader never exceed the rated load
capacity of 80kg.
6.2
STORAGE.
6.2.1 Before storing ensure that the spreader is clean and dry.
6.2.2 store indoors or in a protected area during severe weather and
in the winter months.
6.2.3 never allow material to stay in the hopper for extended periods
of time.
