background image

4.9. 

Place the hopper (6) over the frame tube assembly (1) so  

 

that the shaft protruding from the impeller on the frame tube  

 

assembly locates into the swivel bush on the base of the  

 

hopper.

4.10.  Align the six bolt holes in the hopper assembly with the six  

 

bolt holes on the frame tube assembly and fit the Hex Bolts  

 

M6x40 (9) with the big flat washers M6 (15) at the bolt heads.  

 

Loosely attach the M6 lock nuts (13) as shown in figure 6.  

 

Adjust the hopper assembly over the frame tube assembly  

 

until the impeller is free to rotate without any resistance. fully  

 

tighten the nuts and bolts securing the hopper assembly to  

 

the frame tube assembly.

4.11.  Attach the r-pin (19) to the shaft protruding above the  

 

impeller as shown in figure 7.

4.5.  Attach the hitch tube (2) to the frame tube assembly tube (1)  

 

using hex bolt M6x40 (9), big flat washer M6 (15) and M6 lock  

 

nut  (13) as shown in figure 3. At this stage do not fully tighten  

 

the  nut and bolt. 

4.6.  Attach one brace (3) to either side of the hitch tube (2)  

 

using hex bolt M6x35 (8) and M6 lock nut (13) as shown in  

 

figure 4. Do not fully tighten the nut at this stage

fig.3

fig.4

4.7.  Attach the other ends of the braces (3) to the frame tube assembly  

 

(1) using hex bolt M6x35 (8) and M6 lock nuts (13) as shown in  

 

figure 5. 

4.8.  All nuts and bolts used for the braces (3) can now be fully 

 

tightened

fig.5

fig.6

fig.7

4.12.  Attach a Ø8 flat washer (16) over the loose end of the  

 

adjustable connection rod and insert the rod through the  

 

hole in the fixing plate at the base of the hopper and secure  

 

with a M8 lock nut (14) as shown in figure 8.

4.13.  Place the hopper screen (4) into the hopper (6) so that it sits  

 

squarely on the base. 

4.14.  the spreader is now fully assembled and ready for use. 

Original Language Version

sPB57t    Issue: 1 - 21/06/11

Summary of Contents for SPB57T

Page 1: ...r is fully trained and competent to operate the prime mover before attaching and using the spreader Ensure that all chemical safety instructions are adhered to when handling products for use in the spreader A full range of personal safety equipment is available from your Sealey dealer Always distribute the load evenly Ensure all non essential personnel keep a safe distance when the spreader is in ...

Page 2: ...sembly tube 1 using hex bolt M6x40 9 big flat washer M6 15 and M6 lock nut 13 as shown in figure 3 At this stage do not fully tighten the nut and bolt 4 6 Attach one brace 3 to either side of the hitch tube 2 using hex bolt M6x35 8 and M6 lock nut 13 as shown in figure 4 Do not fully tighten the nut at this stage fig 3 fig 4 4 7 Attach the other ends of the braces 3 to the frame tube assembly 1 us...

Page 3: ...oduct 5 5 The adjustable feed system is controlled by movement of the handle on the hitch tube 2 Operate the spreader at the desired speed and adjust the handle either forwards or backwards until a satisfactory rate of flow is achieved A locking device is provided on the gauge to allow the optimum flow required to be maintained 5 6 Clean the spreader thoroughly after use paying particular attentio...

Page 4: ... ft coverage 10000 sq ft coverage 15000 sq ft coverage 5 1 0lb 0 5lb 0 3lb 10 2 0lb 1 0lb 0 7lb 15 3 0lb 1 5lb 1 0lb 20 4 0lb 2 0lb 1 3lb 25 5 0lb 2 5lb 1 7lb 30 6 0lb 3 0lb 2 0lb 35 7 0lb 3 5lb 2 3lb 40 8 0lb 4 0lb 2 3lb 45 9 0lb 4 5lb 3 0lb 50 10 0lb 5 0lb 3 3lb 55 11 0lb 5 5lb 3 7lb CHART B spreader settings spreader widths materials to be used lbs 1000 sq ft spreader setting small particle spr...

Reviews: