INDEXABLE CARBIDE END MILL
(MT3)
Part No. SM2502ICEM
QUICK VICE
(WIDTH 100MM)
Part No. SM2502QV
42 PIECE CLAMPING KIT
Part No. SM2502CK
7. TROUBLESHOOTING
8. OPTIONAL ACCESSORIES
SYMPTOM
POSSIBLE
CAUSE
CORRECTIVE
ACTION
Motor overheats / no power
Feed is too fast.
Decrease feed speed.
Faulty switch or motor.
Replace faulty part. ( See parts list ).
Overload protection has operated.
Return speed switch to ‘I’ position and restart (See sec.4.10)
Spindle bearing getting hot.
No lubrication.
Apply grease.
Spindle bearing too tight.
Loosen the bearing.
Unbalanced table travel.
Excessive play in table movement.
Adjust the mitre strips. ( Refer to section 6.6 ).
Cut depth too deep for cutting tool.
Decrease the depth of the cut.
Spindle shakes during use.
Spindle bearing gap is too wide.
Reduce the gap or replace the bearing.
The chuck is loose.
Re-seat the chuck in the arbor.
Cutter is blunt.
Sharpen or replace the cutter.
Workpiece
is
loose.
Secure
the
workpiece.
Vertical fine feed not functioning.
Clutch is loose.
Tighten the clutch.
Worm and worm shaft are worn.
Replace worn parts. ( See parts list ).
Hand wheel fixing is loose.
Realign and tighten fixing.
Drill feed still engaged.
Push drill feed hub inwards (See section 4.1)
COLLET
(MT3)
(SINGLES AND SET)
SM2502C04
(DIAM 4MM)
SM2502C06
(DIAM 6MM)
SM2502C08
(DIAM 8MM)
SM2502C10
(DIAM 10MM)
SM2502C12
(DIAM 12MM)
SM2502C14
(DIAM 14MM)
SM2502C16
(DIAM16MM)
SM2502CSET
(4 TO 16MM)
2 FLUTE HSS END MILL
(SINGLES AND SET)
SM2502EM04
(DIAM 4MM)
SM2502EM06
(DIAM 6MM)
SM2502EM08
(DIAM 8MM)
SM2502EM10 (DIAM 10MM)
SM2502EM12 (DIAM 12MM)
SM2502EM14 (DIAM 14MM)
SM2502EM16
(DIAM16MM)
SM2502EMSET (4 TO 16MM)
MILL CHUCK SET (MT3)
CHUCK DIAMETERS
4,6,8,10,12,14,16MM
Part No. SM2502MCS
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
www.sealey.co.uk
Note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without
prior notice.
Important
: No Liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Original Language Version
SM2502 Issue: 3(L) - 26/07/17
© Jack Sealey Limited
