3.2.
Attach a sanding disc (fig 2.A) to the back plate by
removing the self adhesive backing and carefully applying
the disc to the plate.
Note: your model may arrive with a disc already applied.
3.3.
Insert table support rod (fig 1.1) into boss below and to left
of disc (fig 2.X) and lock in place with bolt (fig 1.2).
3.4.
The angle of the table may be adjusted by loosening locking
nut (6) and positioning the angle gauge (5) accordingly.
3.5.
The mitre gauge (fig 2.B) base bar locates in the groove in the table top (fig 1.4).
3.6.
Bolt sander to a stable, fireproof bench or table which is strong enough to take the
weight of the sander and the workpiece.
2. TECHNICAL SPECIFICATION
Belt . . . . . . . . . . . . . . .915 x 100mm
Belt Speed . . . . . . . . . . . . .290m/min
Disc Diameter . . . . . . . . . . . .150mm
Disc Speed . . . . . . . . . . . . .1450rpm
Table . . . . . . . . . . . . . .190 x 125mm
Table Tilt . . . . . . . . . . . . . . . . . . .45
O
Dust Extraction Port . . . . . . . . .38mm
Motor . . . . . . . . . . . . . . .450W 230V
Weight . . . . . . . . . . . . . . . . . .15.5kg
3. ASSEMBLY & ADJUSTMENT
3.1.
Unpack the sander and check contents. Should there be any damaged
or missing parts contact your supplier immediately.
"
WARNING! Before each use
rotate the sanding disc by hand to check it is undamaged and secure. Remove adjusting keys and
wrenches before turning the sander on.
Ensure you wear approved safety goggles, gloves, ear defenders and respiratory protection.
"
WARNING! DO NOT
switch the sander on whilst the workpiece is in contact with the disc or belt
.
Keep all guards and holding
screws in place, tight and in good working order. A guard or other part that is damaged should be first checked to ensure that it will
operate properly and perform its intended function
before
the sander is used, if damaged replace part/s. The safety guards are
mandatory when the sander is used in premises covered by the Health & Safety at Work Act.
4.1.
SANDING BELT (fig 2.G).
4.1.1. If the belt does not run centrally on the drums the tracking should be adjusted by turning knob (fig 2.D).
4.1.2. To stabilise the sanding bed, unscrew support rod (E) until it ‘butts’ up to the underside of the sanding belt bed and lock with nut (F).
4.1.3. The sanding belt bed (G) may be rotated through 90
O
, from the horizontal and locked for operating in a vertical position.
4.1.4. To alter the bed angle, remove the end guard by removing bolt (K1) and two screws on underside of guard (fig 2a), withdraw guard (J)
and replace bolt K1.
4.1.5
Loosen the 14mm clamp nut located adjacent to upper pulley, (behind sanding disc at rear). Pull the sanding belt upright and tighten
the lock nut. Fit the sanding table to mount (fig 2a) and adjust to the desired angle. When returning to horizontal position ensure you
replace the guard.
4.2.
SANDING TABLE (fig 1.4).
4.2.1. The table may be tilted through 45
O
by loosening thumb screw (6) which clamps the angle quadrant (5).
4.2.2. When operating sanding bed (fig 2.G) in the vertical position, mount table (fig 1.4) at the foot of the belt.
a. Remove table assembly and support rod (1). Loosen hex nuts on the underside of table holding table racket (7) steady, and remove bolt form
angle quadrant (5) just under the table at point (S). Align the head of angle quadrant (5) with the inner screw hole on the underside of the
table and secure with bolt.
b.
Insert table support rod (1) into rear mounting hole and fix with locking bolt.
c.
Align table as required and tighten all hex nuts and bolts.
4. OPERATING INSTRUCTIONS
5. OPERATING INSTRUCTIONS
6. DECLARATION OF CONFORMITY
Declaration of Conformity
We, the sole importer into the UK, declare that the product listed here is
in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority,
upon request to Jack Sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
BENCH TOP BELT/DISC SANDER
Model SM14.V4
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
98/37/EC Machinery Directive
93/68/EEC CE Marking Directive
Signed by Steve Buckle
11th October 2006
fig 2
fig 1
"
"
WARNING! Disconnect sander from the electrical supply before performing any service or maintenance.
5.1.
Keep the sander clean and replace a worn or damaged sanding belt or disc.
5.2.
To change sanding belt remove the bottom guard plate of belt bed. End guard and stop may remain in place.
5.3.
Push belt tension lever (fig 2.C) fully to the right. Remove old belt. Place new belt over the two drums (note
direction arrows on the inside of the belt). Move the tension lever back to the left. Replace bed guard and
adjust belt tracking if necessary.
5.4.
Replace sanding disc pad. Remove table and disc guard. Peal off of pad, and stick new pad in place.
5.5.
Periodically lubricate the drive bearings. DO NOT lubricate motor bearing. The motor is a sealed unit.
5.6.
To change the drive belt inside cover (fig 3.Z), remove disc guard (Y) and sanding pad from disc (A). Undo central screw in disc and the
back hex screw by inserting long hex key through access hole in top of guard (M). Remove disc (H). Remove belt cover (Z) and replace
belt. Re-assemble unit.
fig 3
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
SM14.V4 - 2 - 10/10/06
REMOVE SCREWS X 2 TO
REMOVE END GUARD J.
fig 2a
K1
TABLE
MOUNT
