4.
MAINTENANCE.
4.1.
Changing the drill chuck.
To remove the drill chuck open the chuck fully. Locate the internal screw head and undo turning the screw CLOCKWISE (left handed
thread. Stop the chuck from moving by securing the the nut at the base of the chuck (fig1. 5) with a spanner.To replace the chuck
reverse the above process.
4.2.
Cleaning
Keep the drill ventilation slots clean and free from obstructions. If available blow compressed air into the vents to clear any internal
dust (safety goggles must be warn when undertaking this process). Keep the outer case of the drill clean and free from grease.
DO NOT wash with water or use solvents or abrasives.
4.3.
Brushes
must be changed by an authorised Sealey service agent.
,
3.5.
STANDARD DRILLING INSTRUCTIONS.
p
p
WARNING! ensure you wear approved safety goggles and any other safety item required for the job. Remove the chuck key before
using the drill, and ensure the trigger button lock is not locked in position which would result in accidental starting of the drill. Also
ensure that all other safety requirements in chapter 1 are followed.
Ensure drill is unplugged from the mains power supply.
3.5.1. If the material to be drilled is free standing it should be secured in a vice or with clamps to keep it from turning as the drill bit rotates.
3.5.2. When drilling metals, use a light oil on the drill bit to keep it from overheating. Oil will prolong life of bit and improve the drilling action.
3.5.3. For hard smooth surfaces use a centre punch to mark desired hole location. This will prevent bit from slipping as your start to drill.
3.5.4. A pilot hole may be necessary to assist the final drill size through the work piece. Lock a pilot drill (smaller size drill than the finished hole
size) into the chuck. Follow steps 3.5.5 to 3.5.7. below and drill a pilot hole in the middle of the centre punch mark where final hole is
to be drilled. Insert the final sized bit. Hold drill firmly and place the bit at the entrance of the pilot hole and depress the trigger.
3.5.5. Plug drill into mains power supply.
3.5.6. Hold tool firmly and place the bit tip to the point to be drilled.
3.5.7. Depress the trigger to start drill. Move the drill bit into the work piece applying only enough pressure to keep the bit cutting.
DO NOT force or apply side pressure which will elongate the hole.
p
p
WARNING! be prepared for drill binding or break through. When these situations occur the drill has a tendency to grab and kick in the opposite
direction and could cause loss of control. If you are not prepared, this loss of control can result in possible damage and/or personal injury
3.5.8. If the bit jams in the work piece or if the drill stalls, release the trigger switch immediately. Remove the bit from the work piece and
determine the reason for jamming.
3.5.9. For continuous operation, depress the the trigger lock (see 3.3).
3.5.10. The depth gauge may be used to pre-determine the depth of hole (see 3.4).
3.5.11. After working for a lengthy period of time at low speed setting run drill for approximately 3 minutes with no load at highest speed.
3.5.12. When job is complete unplug drill from the mains, remove the drill bit, sharpen if necessary and store accordingly.
3.6.
Work complete.
p
p
WARNING! drill bits become very hot during use. Allow to cool or hold with a cloth for removal.
When you have finished working, unplug from the mains power supply, remove the bit from the chuck, clean drill, clean and if
necessary sharpen the tool bit and store in a safe dry childproof area.
,
Declaration of Conformity
We, the sole importer into the UK, declare that the products listed here are in conformity with the following EEC standards and directives
The construction files for these products are held by the Manufacturer and may be inspected
on request by contacting Jack Sealey Ltd
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Power Tools.
Variable Speed Hammer Drill
Models SD800 & SD1000
73/23/EEC Low Voltage Directive (S.I. 1994/3260)
89/336/EEC EMC Directive (S.I. 1992/2372 &
Amendments)
Signed by Mark Sweetman
2nd May 2003
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions, call us on 01284 757525 for and leave your full name and address including postcode.
SD800 & SD1000 - 2 - 110603
3.2.8
Selection of hammer action / drilling.
When using a masonry drill bit the hammer action can be
used to assist penetration into concrete, stone and masonry.
SD800.
The hammer action selector is a large sliding switch situated on top of the drill. (See fig.4)
To select hammer action slide the selector to the left so that it is adjacent to the hammer symbol
moulded on the side of the case. To disable the hammer action slide the switch in the other direction to
be adjacent to the drill symbol moulded on the other side of the casing.
SD1000.
To use the drills hammer function turn the selector knob on top of the drill (fig.2 item 6)
so that the arrow moulded into it points towards the hammer symbol. To disengage the hammer
function turn the selector knob back to the drill bit symbol
3.3.
DRILL OR TOOL BIT FITTING.
p
p
WARNING! Unplug from the mains power supply before placing
bit into chuck.
Open or close the chuck jaws to a point where the
opening is slightly larger than the drill or tool bit to be used. Also raise the
front of the drill slightly to stop the bit from falling out of the chuck jaws.
Insert the drill bit into the chuck as far as it will go. Place the chuck
key in one of the chuck holes and tighten the chuck securely. (fig 3).
3.4.
DEPTH STOP GAUGE.
Ensure the work piece has a flat surface and is wide enough for the gauge to butt up against when the
required depth has been reached. Measure back from tip of the drill bit to the point at which the drill
must stop. Release clamp/handle and extend the depth gauge to the point at which you wish to stop
drill penetrating further and retighten the handle/clamp. Once drill has reach correct depth the gauge
will butt up against work piece and stop further inward progress.
01284 757500
01284 703534
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
fig 5
fig 4
fig 3
