background image

 

  

Environmental Protection.

  

Recycle unwanted materials instead of disposing of them as  

   

waste. All tools, accessories and packaging should be sorted,  

   

taken to a recycle centre and disposed of in a manner which  

   

is compatible with the environment.

  

WEEE Regulations.

  

Dispose of this product at the end of its working life in compliance   

   

with the EU Directive on Waste Electrical and Electronic Equipment.  

   

When the product is no longer required, it must be disposed of in an  

   

environmentally protective way. Contact your local solid waste  

 

   

authority for recycling information.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this product. 

WARRANTY: 

Guarantee is 12 months from purchase date, proof of which will be required for any claim. 

INFORMATION:

 For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

[email protected]

Sole UK Distributor, Sealey Group, 

Kempson Way, Suffolk Business Park

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

 

  Problem 

Possible Cause 

 

Solution

 

   

  CONNECTED LED is not on. 

The battery is not connected correctly. 

Check for correct connection to the battery.

 

   

Battery voltage is at zero volts. 

Turn everything off in the vehicle and try to

   

 

connect again.

  CHARGING LED is flashing. 

Charger is in abort mode. 

Unplug the charger from the mains supply 

   

 

and plug it back in.

  

   

Battery is sulphated.  

Have the battery checked.

 

   

Battery is defective. 

Have the battery checked.

 

 

 

 

   

  FULL CHARGE LED is on, 

Surface charge voltage is high. 

Replace the battery.

  but battery is not fully charged. 

 

 

 

  

   

Battery voltage is very low and the charger 

Unplug the charger from the mains supply and  

   

detects it as 6V, not 12V. 

plug it back in.

  

  All LEDs light in an erratic manner. 

A button may have been pressed whilst the 

Unplug the charger from the mains supply and

   

charger was being plugged in. 

plug it back in, without touching the control    

  

 

board.

  8.  TROUBLESHOOTING

Original Language Version

SCI6S            Issue: 1 - 21/05/14

©  Jack Sealey Ltd

Summary of Contents for SCI6S






Reviews: