6.6.
CONTINUOUS DRAINAGE
To provide a more efficient performance the self-evaporating system uses the collected water
to cool the condenser coils.
It is recommended not to use the continuous drain method in the cooling mode.
The condensate water evaporates at the condenser and is expelled through the exhaust hose.
6.6.1.
Switch
o
ff
the unit and remove the electrical plug from it’s power source.
6.6.2.
Release the cover from the water outlet opening (
fi
g.13).
6.6.3.
With care push
fi
t one end of the drain hose (
fi
g.13) onto the water outlet (
fi
g.13).
6.6.4.
Securely place the other end of the drain hose over a suitably sized container or drain.
WARNING!
Ensure that the drain hose is straight and free from any kinks and at an inclination
angle downwards of not more than 20º.
DO NOT
allow the open end of the drain hose to be submerged into the water. This may cause
an air lock in the hose.
NOTE:
The condensate water will automatically flow into the container or drain.
7. MAINTENANCE
NOTE:
Maintenance, service and repair must be carried out by qualified person. Contact your Sealey stockist for details.
7.1.
CLEANING
7.1.1.
Switch
o
ff
the unit and remove the electrical plug from it’s power source.
7.1.2.
Clean the unit with soft damp cloth.
DO NOT
use solvents.
7.2.
CLEANING THE AIR FILTER
The air filter requires regular cleaning. A restricted airflow will reduce the efficiency of the system.
It is recommended that air filter is cleaned every two weeks.
DO NOT
operate the unit without an air
fi
lter.
7.2.1.
Switch
o
ff
the unit and remove the electrical plug from it’s power source.
7.2.2.
Remove
the
fi
lter mesh from the unit (
fi
g.1 #4).
7.2.3.
Use a household vacuum to remove any dust from the
fi
lter.
7.2.4.
Turn
the
fi
lter over and rinse the
fi
lter under running water (
fi
g.14).
7.2.5.
Allow
the
fi
lter to dry before reinstalling.
8. STORAGE
8.1.
Turn on the unit and select the low wind ventilation mode. See section 6.2.4.
8.1.1.
Leave in this condition until the drainage pipe becomes dry.
NOTE:
This will help prevent mildew.
8.2.
Switch
o
ff
the unit and remove the electrical plug from it’s power source.
8.3.
Remove the window kit, exhaust hose and drain hose.
8.4.
Drain the remaining water from the unit. See section 6.5.
8.5.
Replace any drainage plugs.
8.6.
Clean
the
fi
lter. See section 7.2.
8.7.
Remove the batteries from the remote control.
8.8.
Store the unit and accessories in it’s original packaging, in safe dry childproof location.
9. TROUBLESHOOTING
SAC9002.V2 Issue 1 24/01/22
Original Language Version
© Jack Sealey Limited
fi
g.13
fi
g.14
SYMPTOM
POSSIBLE CAUSE
REMEDY
The unit is not
working
No power
Connect to power source and turn the unit ON
Full water indicator is illuminated
Drain the water
Low room temperature
Change the set temperature
The unit works
with reduced
capacity
Dirty air filter
Clean the air filter as required
Air ducts are blocked
Clear obstacles. Re-position unit into clear space
Doors or windows open
Close the doors and windows
Incorrect mode and temperature selected
Select correct mode and temperature to suit desired
application
Detached exhaust hose
Securely reattach exhaust hose
Water leakage
Spillage when moving the unit
Empty the water tank before moving the unit
The drain hose is kinked or bent
Straighten the drain hose
Excessive noise
The unit is on an uneven surface
Place the unit onto a flat horizontal surface
Loose, vibrating parts
Check for loose parts and re-tighten
Water flowing sound
Normal sound of refrigerant flowing
Error
codes
E0
Communication faults between main PCB and
display PCB
Contact Sealey service centre
E1
Ambient temperature sensor fail
Contact Sealey service centre
E2
Coil temperate sensor failures
Contact Sealey service centre
Ft
Condensate water high level alarm
Drain the water
