From
pump
To receiver
Decompression
tube from switch
fig.1
Non return valve
Hose reel tidy
Ball valve
Original Language Version
SAC3203B3PH Issue No: 1 - 27/10/14
© Jack Sealey Limited
1.1
ELECTRICAL SAFETY.
WARNING! It is the user’s responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and all
electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that are
plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current
Device by contacting your Sealey dealer.
You must
also read and understand the following instructions concerning electrical safety.
1.1.1 The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
Electrician at least once a year, using a Portable Appliance Tester (PAT).
1.1.2 The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance, and the
safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified Electrician.
1.1.3 Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.1.1. & 1.1.2.
above and use a Portable Appliance Tester (PAT).
1.1.4 Ensure that cables are always protected against short circuit and overload.
1.1.5 Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power connections, to ensure that
none are loose.
1.1.6
Important:
Ensure the voltage marked on the product is the same as the electrical power supply to be used and check that plugs are fitted with the correct
capacity fuse. If an electrical fuse blows, ensure it is replaced with an identical fuse type and rating.
1.1.7
DO NOT
pull or carry the powered appliance by its power supply lead or output cables.
1.1.8
DO NOT
pull power plugs from sockets by the power cable.
1.1.9
DO NOT
use worn or damage leads, plugs or connections. Immediately replace or have repaired by a qualified Electrician. This
particular compressor is supplied without a mains plug. Follow the instructions below regarding the fitting of an appropriate plug.
1.2
MODEL SAC3203B3PH REQUIRES A 415V 3 PHASE SUPPLY AND MUST HAVE AN APPROPRIATE PLUG FITTED.
WARNING! ELECTRICAL INSTALLATION OF THE COMPRESSOR TO A 3 PHASE 415VOLT SUPPLY MUST ONLY BE CARRIED OUT BY A
QUALIFIED ELECTRICIAN.
Ensure the power supply cable is connected to the Earth.
1.2.1 This product must be fitted with a 3 phase plug wired as illustration in (fig.2), wired to an appropriately fused supply.
Connect GREEN/YELLOW wire to Earth ‘E’
Connect BROWN wire to L1 Terminal.*
Connect BLACK wire to L2 Terminal.*
Connect the GREY wire to L3 Terminal.*
*NOTE: The cable core colours found in the mains cable on this compressor are consistent with Amendment 2 to 7671:2001. When completed,
check there are no bare wires, that all wires have been connected correctly and the cable restraint is tight.
WARNING!
IT IS ESSENTIAL TO OBSERVE ANTI-CLOCKWISE (fig.1) PULLEY DIRECTION ON INITIAL START UP. IF CLOCKWISE
OBSERVED, STOP IMMEDIATELY AND CONSULT A QUALIFIED ELECTRICIAN TO INVERT 2 PHASES.
1.2.2
DO NOT
use this product with a standard extension cable. Only use ARMOURED extension cable
IMPORTANT USER INFORMATION!
Over-current protection of the power circuit is required in accordance with 7.2 of EN 60204-1:2006. The
supply disconnecting device to be in accordance with 5.3 of EN60204-1:2006. Ask a qualified electrician about compliance. The use of extension
leads to connect these compressors to the mains is not recommended.
(Grey) to L3
'E' Earth
green/yellow
Mains
cable
(Black) to L2
(Brown) to L1
fig.2
IMPORTANT!
Anti-clockwise
rotation
(label on guard)
see 1.2.1
INSTRUCTIONS FOR:
COMPRESSOR 200LTR BELT DRIVE 3.0HP
415V/3PH WITH FRONT CONTROL PANEL
MODEL NO:
SAC3203B3PH
1. SAFETY
Control Panel
(fig.7)
Swivel castor with brake
2-Pneumatic
tyres 1.5bar
Receiver
Switches
(fig.8)
Motor
3~ph
Pump
(fig.5)
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL
INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
