Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
Follow all workshop safety rules, regulations, and conditions when using wrench.
WARNING!
Disconnect from air supply before changing accessories or servicing.
Maintain the
wrench in good condition and replace any damaged or worn parts.
Use
genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
Only use impact sockets which are specifically designed for use with a ratchet wrench.
Wear approved safety eye/face shield, ear defenders, and hand protection.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and non-essential persons away from the working area.
DO NOT
use the wrench for a task it is not designed to perform.
WARNING! DO NOT
use wrench if damaged or thought to be faulty. (Contact Service Agent).
DO NOT
use wrench unless you have been instructed in its use by a qualified person.
DO NOT
carry the wrench by the air hose, or yank the hose from the air supply.
DO NOT
operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
carry wrench with your hand on the power trigger in order to avoid unintentional starting.
DO NOT
direct air from the air hose at yourself or others.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
WARNING!
The warnings, cautions and instructions referred to in this manual cannot cover all
possible conditions and situations that may occur. It must be understood that common sense
and caution are factors which cannot be built into this product, but must be applied by the
operator.
INSTRUCTION FOR:
SA609, SA610
2.
INTRODUCTION & SPECIFICATIONS
MODEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA609 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SA610
Drive size . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/8”Sq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/2”Sq
Max torque . . . . . . . . . . . . . . . . . . . . . . . . . . . .50lb.ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50lb.ft
Air consumption . . . . . . . . . . . . . . . . . . . . . . . . 5cfm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5cfm
Operating pressure. . . . . . . . . . . . . . . . . . . . . . 90psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90psi
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.9kg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.9kg
Noise-Pressure. . . . . . . . . . . . . . . . . . . . . . . . . 98dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98dB
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.5m/s² . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5m/s²
Innovative design flexible ratchet head allows 30° angle adjustment both directions. Ratchet yoke
designed and manufactured to provide additional strength, prolonging the working life. Reversible
for use in either direction and trigger operated power control. Rear exhaust with baffle reduces
noise level and oil spray. Suitable for use in the professional workshop.
AIR FLEXI-HEAD RATCHET WRENCH 3/8"& 1/2" Sq DRIVE
Original Language Version
SA609, SA610 Issue: 2 - 10/11/09
