Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations
are adhered to when using this equipment.
WARNING!
Disconnect from air supply before changing accessories or servicing.
Maintain the
tool in good condition and replace any damaged or worn parts.
Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
Wear approved safety eye/face shield, ear defenders and hand protection.
Keep fingers clear of blades.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and non essential persons away from the working area.
DO NOT
use the tool for a task it is not designed to perform.
WARNING! DO NOT
use tool if damaged or thought to be faulty. Contact Sealey service agent.
DO NOT
use tool unless you have been instructed in its use by a qualified person.
DO NOT
carry the tool by the air hose, or yank the hose from the air supply.
DO NOT
operate tool if you are tired or under the influence of alcohol, drugs or intoxicating
medication.
DO NOT
carry tool with your hand on the power trigger in order to avoid unintentional starting.
DO NOT
direct air from the air hose at yourself or others.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
WARNING: The warnings, cautions and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
that common sense and caution are factors which cannot be built into this product, but must
be applied by the operator.
INSTRUCTIONS FOR:
AIR SCISSORS
MODEL No:
SA55.V2
2. INTRODUCTION & SPECIFICATION
Max. Cutting Capacity: 1.2mm(Steel) 1.5mm(Aluminium)
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . 4.3cfm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Inlet Size: . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4”BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4kg
Replacement Blade Left: . . . . . . . . . . . . . . .SA55.V2-34
Replacement Cutter Right:. . . . . . . . . . . . . .SA55.V2-35
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . 96.53dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . 85.53dB(A)
Vibration: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.78m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . 0.5868m/s²
Polished aluminium housing with textured grip handle. Suitable for accurately cutting metal sheet.
Unlike air shears this tool is ideal for trimming ragged sheet edges to gain a flat finish. Handle
exhaust helps reduce noise level.
Original Language Version
SA55.V2 Issue: 2(SP) - 12/11/13
© Jack Sealey Limited
