background image

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE

WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.

SAFETY INSTRUCTIONS

p

WARNING!

Ensure Health & Safety, local authority, and general workshop practice 

regulations are adhered to when using this equipment.

p

WARNING!

Disconnect from air supply before changing accessories or servicing.

3

Maintain the sander in good condition (use an authorised service agent).

3

Replace or repair damaged parts. 

Use genuine parts only. Non-

authorised parts may be dangerous and will invalidate the warranty.

3

Use in suitable clean and tidy working area, free from unrelated 

materials and ensure there is adequate lighting.

3

Before each use check abrasive pads for condition. If worn or 

damaged replace immediately.

3

Ensure the abrasive pad rating is the same as, or, greater than 

the RPM rating of the sander.

3

Ensure there are no flammable or combustible materials near 

the work area.

p

WARNING! 

Always wear approved eye, face and hand protection 

when operating the sander. 

3

Use dust / respiratory protection in accordance with COSHH regulations. 

3

Depending on the task, sander noise level may exceed 85dB in which case wear safety ear defenders.

3

Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery, and contain and/or tie back long hair.

3

Wear appropriate protective clothing and keep hands and body clear of working parts.

3

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

3

Keep children and unauthorised persons away from the working area.

3

Check moving parts alignment on a regular basis. 

3

Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.

3

Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.

3

Avoid unintentional starting.

p

WARNING!

Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi 

3

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure

that all connections are secure.

3

Prolonged exposure to vibration from this sander poses a health risk. It is the operator’s responsibility to correctly 

assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.

7

DO NOT use the sander for a task it is not designed to perform. 

7

DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.

7

DO NOT use cloth backed sanding pads. Use only appropriate paper adhesive pads, following pad instructions. 

p

WARNING!

DO NOT sand any materials containing asbestos.

7

DO NOT carry the sander by the hose, or yank the hose from the air supply.

7

DO NOT place attachments close to your face and do not point at other persons or animals.

7

DO NOT operate sander when you are tired, under the influence of alcohol, drugs or intoxicating medication.

7

DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and 

including waste wiping or cleaning rags etc.

7

DO NOT attempt to attach a grinding disc to this sander since the machine speed of 18,000 rpm 

would cause a disc to shatter.

SA10 - 0016 - (3) -121201

INSTRUCTIONS FOR : 

AIR OPERATED 

HIGH SPEED ORBITAL SANDER

MODEL NO : 

S

S

A

A

1

1

0

0

SA10

PARTS INFORMATION FOR : 

AIR OPERATED 

HIGH SPEED ORBITAL SANDER

MODEL NO : 

S

S

A

A

1

1

0

0

SA10

01284 757500

E-mail:

[email protected]

01284 703534

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component

parts without prior notice. 

IMPORTANT: 

No liability is accepted for incorrect use of this equipment. 

WARRANTY: 

Guarantee is 12

months from purchase date, proof of which will be required for any claim. 

INFORMATION: 

Call us for a copy of our latest catalogue

and promotions on 01284 757525 and leave your full name and address including your postcode.

Sole UK Distributor, Sealey Group

, Bury St. Edmunds, Suffolk.

ITEM  PART NO. 

DESCRIPTION

03

SA10/96-03

HANDLE

07

SA10/96-07

TRIGGER

16

SA10/96-16

PIN

22

SA10/96-22

BALL SEAT

23

SA10/96-23

STEEL BALL

24

SA10/96-24

SPRING

26

SA10/96-26

PIN

28

SA10/96-28

PUSH ROD

28P SA10/96-28P O-RING

29

SA10/96-29

INTAKE BUSH

30

SA10/96-30

O-RING

31

SA10/96-31

O-RING

32

SA10/96-32

AIR REGULATOR

40

SA10/96-40

HOUSING LOCK RING

41

B/6201Z

BALL BEARING

42

SA10/96-42

REAR END PLATE

ITEM  PART NO. 

DESCRIPTION

43

SA10/96-43

CYLINDER

44

SA10/96-44

ROTOR BLADE

45

SA10/96-45-2 ROTOR, 98MM

46

SA10/96-46

BUSHING

47

SA10/96-47

FRONT END PLATE

48

SA10/96-48

CYLINDER HOUSING

49

SA10/96-49-2 ADAPTOR 30MM

50

SA10/96-50

HOLDING TOOL

51

SA10/96-25

BACKING DISC 3”

52

SA10/96-26

BACKING DISC 4-1/2”

53

SA10/96-27

BACKING DISC 5-1/2”

54

SA10/96-54

LOCK,ADAPTOR

SA10/DG

DISC GUARD

SA10/08

SPRING

Issue No 

1

Issue date  14/11/01

Reviews: