4.3.
INSTALLING THE SPRAY WAND FIG 2
4.3.1.
Fit the spray wand into the gun and rotate it until the two parts are completely locked.
4.3.2.
Snap the desired nozzle onto the quick-connect collar until it clicks into place.
4.3.3.
Connect the high pressure hose to the trigger gun
4.3.4.
Connect the sliver end of the high-pressure hose to the trigger gun and twist the nut
as indicated to secure the
connection.
4.3.5.
Connect the high-pressure hose to the water outlet.
4.3.6.
Connect the other end of the high-pressure hose to the water outlet on the washer
and twist the black rotatable end-
piece as indicated to secure the connection.
4.3.7.
Connect the garden hose to the water inlet.
4.3.8.
Connect the garden hose adaptor (female coupler) to the water inlet of the pressure
washer, then thread your garden
hose (male end) into the garden hose adaptor.
5. OPERATION
5.1.
Position the appliance on an even surface.
Insert the mains plug into the socket.
5.2.
WATER SUPPLY
NOTE:
For connection values, see type plate.
WARNING!
Impurities in the water can damage the high-pressure pump and the accessories.
5.2.1.
Attach garden hose to water supply
8
DO NOT
connect to potable water system.
5.3.
The water supply must not exceed 0.7MPa.
5.4.
The washer must only be used with clean water, use of unfiltered water containing corrosive chemicals will damage the washer.
5.5.
Bleed the device as follows prior to operation:
5.5.1.
Turn on the appliance “OFF/ON”
5.5.2.
Unlock the lever of the trigger gun.
5.5.3.
Push the lever of the trigger gun, the device will switch on.
5.5.4.
Let the device run (max. 2 minutes) until the water exits the trigger gun without bubbles.
5.5.5.
Release the lever of the trigger gun.
5.5.6.
Lock the lever of the trigger gun.
WARNING!
Dry running of more than 2 minutes leads to damage of the high-pressure pump. If the appliance does not build up
pressure within 2 minutes, switch the appliance off and proceed in accordance with the instructions in section 7 “Troubleshooting”
5.6.
HIGH PRESSURE OPERATION
5.6.1.
Keep a distance
of at least 30 cm when using the jet for cleaning painted surfaces to avoid damage.
5.6.2.
Make sure the on/off switch is set to “OFF/O” (fig.7) and insert the plug into a properly installed socket.
5.6.3.
The washer must be used on a secure and stable surface in a standing, upright position.
5.6.4.
Connect the product to power and water supply as described.
5.6.5.
Open the water supply
5.6.6.
Hold the spray gun with both hands.
5.6.7.
Direct the nozzle of the chosen accessory away from you towards the surface to be cleaned.
5.6.8.
Unlock the trigger and press it until a constant amount of water flows through the nozzle, to allow air trapped in the hose to escape.
5.6.9.
Release the trigger.
5.6.10.
T
urn on the switch “OFF/ON”.
5.6.11.
H
old the spray gun with both hands. Direct the water jet to the object to be cleaned and press the trigger. Release the lever of the
trigger gun; the device will switch off again and stop the water jet. High pressure remains in the system.
WARNING!
Beware of kickback when pressing the trigger!
fig.3
fig.4
fig.5
fig.6
fig.7
Original Language Version
© Jack Sealey Limited
fig.2
P
W2000PA Issue 2 (2) 10/02/21
