140BAR PULL ALONG PRESSURE WASHER
WITH TSS 1800W
MODEL NO:
PW2000PA
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey Stockist.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualified electricia
n.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8
DO NOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! RISK OF FLUID INJECTION.
This washer operates at fluid pressures and velocities high enough to penetrate human
and animal flesh. If there is an occurrence of fluid injection seek medical help immediately
WARNING!
Stop the engine and disconnect the mains water supply before changing accessories or performing any maintenance.
WARNING! DO NOT
operate the washer if damaged. Replace or repair using recommended parts only. Unauthorised parts may be
dangerous and will invalidate your warranty. Use authorised Service agent only.
WARNING! DO NOT
direct jet against yourself or others in order to clean clothes or foot-wear.
9
Keep the washer in good condition. Regular maintenance will give the best and safest performance.
9
Ensure you comply with the water supply company regulations before connecting to the mains. If you are connecting to the mains
drinking water supply ensure you have a back flow preventer valve installed.
9
The water supply hose must be reinforced and have an internal diameter of 13mm (1/2”). The minimum water supply rate must be at
least equal to the cleaner capacity. The water temperature must not exceed 50°C and the pressure must not exceed 10bar.
WARNING!
DO NOT
operate the washer without the water supply connected. To do so will damage the machine.
9
Position the washer as near as possible to the mains water supply.
9
Only use recommended washing detergents. Failure to do so may cause corrosion to equipment and hoses.
WARNING!
Use the washer on a flat, level surface, in a horizontal position. Failure to do so will invalidate your warranty.
9
Wear safety goggles and adequate protective clothing and anti-slip rubber soled footwear.
WARNING!
The high pressure jet must be used with caution. Ensure you aim the lance correctly at the work surface. Failure to do so
may scatter loose particles at the same force as the water pressure, resulting in possible damage or personal injury.
9
Keep all persons and animals at a safe distance from the hose working area. It is difficult to give an exact safe distance as it will
depend upon your circumstances. We recommend at least 15 metres (16 yards). Also ensure other persons are aware before you
start to depress the washer trigger.
9
Hold the gun firmly for it will tend to “kick” backwards when you first pull the trigger.
Recommended fuse rating
13 Amp
P
W2000PA Issue 2 (2) 10/02/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
DO NOT direct jet
against yourself,
other persons,
animals, electrical
equipment or the
machine itself
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
Electrical shock
hazard
