InstructIons for:
INFRARED GAS HEATER
MoDEL no:
LP13.V2
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. CONTENTS
1.1.
GENERAL SAFETY
IMPORTANT:
the LP13.V2 is a mobile, propane-fired, unvented, infrared space heater for
commercial
applications only.
DO NOT use
domestically.
WARNING!
Use only in well ventilated spaces of more than 15m3 to prevent an accumulation of dangerous combustion gases.
DO NOT
operate heater in basements or otherwise below ground level.
WARNING! Heater will become very hot during use.
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
familiarise yourself with the application and limitations of the heater, as well as the potential hazards.
WARNING!
Disconnect the heater from the gas supply before performing any maintenance.
Maintain the
heater in good condition (use an authorised service agent).
replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING!
Keep all guards and holding screws in place, tight and in good working order. check regularly for damaged parts. A guard or
any other part that is damaged must be repaired or replaced before the heater is next used.
Keep the heater clean for best and safest performance.
Ensure the propane bottle is in a stable upright position before igniting the heater.
DO NOT
use with the bottle in any position other than upright.
DO NOT
use any fuel other than propane.
Ensure there are no flammable or combustible materials within 2 metres of the heater and that nothing, including walls, is less than 500mm
from any surface of the heater.
DO NOT
use the heater where there are flammable liquids, solids or gases such as paint solvents, etc.
Keep gas hose away from heat, oil and sharp edges. regularly check hose for wear and ensure that all connections are secure.
DO NOT
move the heater when it is operating.
DO NOT
use the heater for any purpose other than that for which it is designed.
DO NOT
operate the heater if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT
adjust, or tamper with, the regulator.
DO NOT
allow untrained persons to operate the heater.
DO NOT
operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use disconnect from the gas supply and store in a safe, dry, childproof area.
In the event of a gas leak immediately close the bottle valve, extinguish any flame and then place equipment in a well ventilated area,
preferably outdoors, and away from any heat sources (including strong sunlight). rectify cause of leakage.
If a persistent leakage occurs notify a qualified service engineer.
DANGER!
If the burner remains alight after the bottle valve has been closed
DO NOT
attempt
to remove burner and/or regulator from the bottle. Contact your gas supplier immediately.
ceramic plaque type heater. Mounts on the rim of a propane cylinder. Adjustable output from
9,200 to 17,000Btu/hr. supplied with 700mm of hose and fixed regulator. DVGW Approved. Gas
bottle not included.
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LP13.V2
Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Propane
Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9,200-17,000Btu/hr
Fuel Consumption. . . . . . . . . . . . . . . . . . . . . 0.216-0.400kg/hr
3.1.
Content
3.1.1. check content against the list below and, in the event of shortages or damage,
contact your supplier.
contents:
• Heater mounting bracket
• Wing nut with hinge bolt and serrated washer
• Heater assembly
• Hose and gas bottle regulator
2. INTRODUCTION & SPECIFICATION
fig.1
4. ASSEMBLY
4.1.
Assembly (See fig.2)
4.1.1. fit the mounting bracket to the heater assembly using the wing nut, hinge bolt and serated washer. the bracket should be
mounted on the right hand side of the mounting flange as the heater faces you. Ensure that the side of the clamping channel with
two bolts is facing forwards,
4.1.2. fit the channel section of the support bracket over the shroud of the propane bottle and clamp in place using the three bolts.
Be sure to fit the channel with the
two
screws on the outside of the shroud and
one
, on the inside, as shown below.
4.1.3. fit the regulator to the bottle by screwing the PoL nut anticlockwise into the port of the gas bottle valve. tighten nut with spanner.
Original Language Version
LP13.V2 Issue: 2 - 25/03/10
