Schaefer HotZone Patio Heater Installation & Operation Instructions Download | Manualshive

Page: 1 / 12

background image

Schaefer HotZone®

HZE Series Electric Spot Heater

800-779-3267

[email protected] • www.schaeferfan.com

High Output Infrared Heater - 1500/3000 Watt

INSTALLATION & OPERATION INSTRUCTIONS

3019762

HotZone® Portable Heater

HotZone®

Wall Mount

Heater

HotZone®

Patio Heater

HotZone® Universal

Fixed Mount Heater

** HOTZONE® HEATERS MUST BE INSTALLED BY A LICENSED ELECTRICIAN. **

1
2
3
...
»

Summary of Contents for HotZone Patio Heater













Reviews:

No comments

Related manuals for HotZone Patio Heater

Brand: wallas Pages: 39

Brand: York Pages: 204

Brand: Bestron Pages: 24

AUBURN EFSXB-15ABLK

Brand: Estate Design Pages: 9

Brand: HISEER Pages: 8

Brand: Noritz Pages: 26

Brand: CALEFFI Pages: 16

Brand: L.B. White Pages: 30

Brand: Lampoassa Pages: 62

Brand: E-gas Pages: 10

Brand: NuTone Pages: 2

Brand: SureCall Pages: 16

EMERALD E63-NG1

Brand: Waterford Pages: 24

Brand: American Standard Pages: 8

Brand: Star Progetti Pages: 41

Brand: Heatrex Pages: 5

EUROSTOVE SRE 301 -

Brand: Eurostove Pages: 2

Brand: anko Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands