fig.5
9.
FILTER CLEANING
9.1.
Handle the filter carefully when cleaning or installing. Unlock and carefully remove the cartridge filter and inspect it for damage. A filter
that has small holes or tears in it will not perform efficiently and should be replaced.
9.2.
To clean a dry filter, tap it inside a waste bin. (The cartridge filter is designed for dry vacuuming only). Should the filter be inadvertently
wetted it should be rinsed
from the inside
and allowed to air dry for 24 hours.
9.3.
DO NOT
use the filter wet as the filter will clog quickly and be very difficult to clean.
9.4.
Fit a new/cleaned filter over the filter basket
9.5.
Lock in place as described in 7.1.2. (0mm clearance).
10.
MAINTENANCE
10.1.
Ensure the machine is unplugged from the power supply.
10.2.
Disconnect the hose from the drum container.
10.3.
Undo the clasps and remove motor housing from the drum container.
10.4.
Clear out any dirt or debris from the drum container and hoses.
10.5.
Frequently clean the seat where the safety float slides and inspect it periodically to check its integrity.
10.6.
Clean the foam filter by washing it in a mild soapy solution.
10.7.
Check the power cable to make sure that it is not damaged.
11. CONSUMAbLES
Locking Cartridge Filter (Must be used for dry vacuuming): Model no: DFS35CF
Foam
Filter:
Model
no:
DFS35FF
IMPORTANT! IF THE MACHINE IS USED WITHOUT A FILTER FITTED THIS MAY CAUSE
DAMAGE TO THE MOTOR AND YOUR GUARANTEE WILL bE INVALIDATED.
ALWAYS KEEP A SPARE CARTRIDGE FILTER HANDY.
Category M Dust Bags:
Model no. DFS35PB
12. TROUbLESHOOTING
fig.6
fig.7
Symptom
Possible causes
Solutions
Vacuum will not operate
no power supply
Check power supply - cable, breakers, fuses.
Faulty power cable
Unplug and check the power cable. If
damaged have it replaced by your local Sealey
dealer.
Container full
Empty container
Dust expelled from the motor cover
Cartridge filter missing or damaged
Fit cartridge filter or replace damaged filter
Reduced efficiency and increased motor/
speed vibration/orange light (C)
There is a blockage in the nozzle/hose/
drum inlet/ filter.
See 7.1.4.. Check nozzle, hose and container inlets
and clear any blockages found. Remove filter and
clean it or install new filter.
noTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
no liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Environmental Protection
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the EU Directive on
Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed
of in an environmentally protective way. Contact your local solid waste authority for recycling information.
PC35110V | Issue 3(I) 07/10/16
Original Language Version
© Jack Sealey Limited
Parts support is available for this product.
To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk,
email [email protected] or telephone
01284 757500.
