PC200SD110V.V2 Issue No.2 22/10/09
Original Language Version
5. WeT vAcUUm cLeANING
WARNING!
Ensure you read, understand and apply Section 1 ‘Safety
Instructions’. Reminder:
Remove plug from power supply before
opening unit. DO NOT vacuum solvents, explosives, inflammable and/or
hazardous liquids such as petrol, oil, spirits, paint, thinners, acids etc.
5.1
ensure the machine is unplugged from the power supply. (fig.4.1) make sure
the tank is clean and free from dust and dirt.
5.2
remove the cartridge filter and fit a foam filter over the filter basket. (fig.4.2)
refit the power head onto the drum.
5.3
to the same flexible hose used in dry cleaning fit the desired nozzle. (fig.4.3)
5.4
ensure the switch is ‘off’ (position ‘0’) before plugging into the power supply.
(fig.4.4)
5.5
Press the switch to ‘on’ (position ‘I’). (fig.4.5)
Note:
to vacuum large quantities of liquid, from a sink or tank etc, do not immerse
the nozzle completely in the liquid, leave a gap at the top of the nozzle opening to
allow an air inflow. the machine is fitted with a float valve which stops the suction
action when the tank has reached its maximum capacity. the user will notice an
increase in motor speed. When this happens, turn off the machine, disconnect from
power supply, remove the power head from the container and empty the liquid into a
suitable receptacle or drain. (fig.4.6)
to continue vacuuming, refit the power head and proceed. After wet vacuuming, turn
the machine off and unplug from power supply. empty the container and clean and
dry the inside and outside before storage.
Remember!
After wet vacuuming the foam filter must be removed and a cartridge
filter must be fitted before dry vacuuming again.
WARNING! Not designed for liquid storage. Always empty liquids after
use and before storing.
wARNINg! Ensure you read, understand and apply Section 1 ‘Safety
Instructions’. Reminder: DO NOT vacuum hazardous substances. use
of
an incorrect cartridge filter will invalidate your warranty.
4.1
ensure the machine is unplugged from the power supply. (fig.3.1)
4.2
remove the power head and with the raised rim uppermost fit the cartridge
filter tube down over the filter basket and push fully home. Place the locking
disc onto the top of the filter and turn the locking bar until the latch drops
into the slot in the top of the filter basket. Continue turning until the filter is
fully locked down. (fig.3.2)
4.3
reposition the power head onto the drum body, and clip in place. (fig.3.3)
4.4
Insert the larger end of the flexible hose into the front inlet on the container
and lock in place. Push the required attachment onto the free end of the
hose. (fig.3.4)
4.5
Plug in the power supply. (fig.3.5)
4.6
Switch to the ‘on’ (position ‘I’). (fig.3.6)
4.7
When you have completed vacuuming, press the switch to ‘off’.
4. DRY vAcUUm cLeANING
6. BLOWING
6.1
Push the large end of the flexible hose into the blow
connection in the top section. (fig.5.1)
6.2
ensure the power switch is turned off (fig.5.2) and plug in
the power supply. (fig.5.3)
6.3
Switch on the power (position ‘I’). (fig.5.4)
6.4
the unit will now blow through the hose and can be
used to clear obstructions within the pipe. (fig.5.5)
WARNING!
If after a few seconds the hose is still
blocked turn off the unit and clear the hose manually.
fig.3
fig.5
fig.4
3.10
Align the arrow symbol on the large end of the vacuum hose with the pin on the front inlet of the drum. Push the fitting
into the inlet and lock in place by turning the fitting clockwise. (fig.2.9)
3.11
Choose the desired nozzle and push it onto the telescopic suction tube. (fig.2.10)
