1.
safety instructions
1.1 GeneraL
Ensure the spotlight is correctly charged before initial use.
WarninG!
The lens becomes very hot during operation.
Do not
cover or block the lens during use.
Do not
shine directly into eyes.
Do not
stand the spotlight near any surface or item that may be adversely effected by the heat generated from the lens.
Do not
allow children to use the spotlight.
Do not
use if the battery or the spotlight casing is damaged.
Do not
handle lamp bulb with your fingers. Use a soft lint-free cloth.
Only use the supplied battery and chargers with this spotlight.
When not in use store the spotlight in a safe, dry, childproof location.
1.2 Battery safety instructions
WARNING! Powered by a sealed lead-acid battery which is dangerous if not handled with care to avoid damage, fire, corrosion or
personal injury.
Charge battery prior to first use. The battery pack will have been shipped in a low charge state.
Use only the charger provided to charge the battery.
Do not
charge battery when room temperature is below 10°C (50°F) or above 40°C (104°F).
Do not
attempt recharging the battery by means of an engine generator or a DC power source (other than with in-car charger provided).
Do not
short-circuit the battery by linking both terminals with a metal object, or your fingers etc.
Do not
store the battery (or spotlight) in locations where the temperature may exceed 40°C (104°F) such as outside sheds, above heaters,
or metal buildings in summer.
WARNING! Dispose of spent battery correctly as it contains acid.
DANGER!
Do not
attempt to dismantle the battery pack.
For safety and environmental reasons
Do not
discard in domestic waste or by burning.
onLy
discard or recycle according to local waste
authority regulations.
WARNING! DO NOT allow a leaking battery to come into contact with your skin. If you come into contact with battery fluid take
immediate action:
a) Skin contact: Wash immediately with soap and water.
b) Eye contact: Flush eye immediately with cool, clean running water for at least 15 minutes and seek immediate medical attention.
1.3 eLectricaL Mains PoWer safety
ONLY USE THE SUPPLIED CHARGER PLUG (FIG.1.2) FOR CHANGING bATTERY FROm THE mAIN ELECTRICAL POWER SUPPLY.
WarninG!
It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCb (Residual Current Circuit
breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with all
electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCb. You must also read
and understand the following instructions concerning electrical safety.
1.3.1 The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the
appliance, and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.3.3 You must ensure that you:
Inspect the charger (fig.1.2) plug, cable and adaptor (C) for wear and damage to ensure items are safe before connecting to the mains
power supply. If worn or damaged
Do not
use.
Check supply circuit is protected against short circuit and overload.
iMPortant:
Check that the voltage marked on the charger plug is the same as the power supply to be used.
Uncoil the power cable between charger and plug.
Do not
pull charger power lead, or pull the charger plug from the mains
socket by the power lead.
Do not
use any other type of mains charger with this product.
Do not
try to open or dis-assemble the charger plug.
Do not
use charger plug to charge or power any other electrical item.
Do not
get charger wet, or use in wet, damp conditions (for indoor use only).
WarninG!
NEVER substitute a standard 13Amp 3 pin plug, or any other type
of plug, for the charger plug.
cable extension reels:
If a cable extension reel is used it should be fully
unwound before connection. A cable reel with an RCD fitted is recommended
since any product which is plugged into the cable reel will be protected.
1.4 12V VeHicLe cHarGe aDaPtor
ONLY USE THE SUPPLIED DC ADAPTOR (fig.1.1) FOR CONNECTING TO
A VEHICLE 12V SOCKET. The adaptor will reduce voltage for 6V charging.
Apply safety instruction 1.3.3 where applicable and read 2.5 for use.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT:
PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents, WarninGs anD cautions. use
tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH it is intenDeD. faiLure to Do so May cause DaMaGe anD/
or PersonaL inJury anD WiLL inVaLiDate tHe Warranty. PLease KeeP instructions safe for future use.
INSTRUCTIONS FOR:
recHarGeaBLe
HaLoGen sPotLiGHt
mODEL No:
ML2
mainsCharger. . . . . . . . mL2.C
Car Charger . . . . . . . . . mL2.CC
Charger Adaptor . . . . . . mL2.CA
battery Pack . . . . . . . . . mL2bP
fig.1
Original Language Version
mL2 Issue: 3 - 20/12/11
