![background image](http://html.mh-extra.com/html/sealey/mc454/mc454_quick-start-manual_1225635001.webp)
hYDRAULIC MOTORCYCLE LIFT 450KG CAPACITY
model no:
MC454
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! ThIS LIFT IS ONLY SUITABLE FOR MOTORCYCLES WhICh hAVE A CENTRE STAND.
WARNING! Ensure the bike is adequately strapped onto the platform before operating.
9
maintain the
lift in good condition (use an authorised service agent).
9
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use a qualified person to lubricate and maintain the lift.
DO NOT
use brake fluid to top up hydraulic unit.
9
locate the lift in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the lift and the bike.
DO NOT
operate the lift on tarmacadam, as the surface may be unstable.
9
Keep the lift clean for best and safest performance.
9
The maximum bike weight is 450kg.
DO NOT
exceed this rated capacity.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
maintain correct balance and footing, do not over reach. ensure the floor is not slippery and wear non-slip shoes.
9
ensure the bike is adequately secured to the lifting platform with appropriate straps.
9
Before lifting check that there are no overhead obstructions.
9
When platform has been raised to the working height ensure the locking bar is engaged to prevent accidental lowering.
9
Keep children and unauthorised persons away from the work area.
9
The lowering speed will vary according to the weight of the load and the amount by which the release pedal is depressed.
8
DO NOT
use the lift for a task it is not designed to perform.
8
DO NOT
operate the lift if damaged.
8
DO NOT
exceed the rated capacity of the lift.
8
DO NOT
operate the lift when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
allow untrained persons to operate the lift.
8
DO NOT
attempt to transport a load on the lift. The lift must only be used in a static position for raising and lowering loads.
8
DO NOT
make any modifications to the lift and
DO NOT
adjust or tamper with the safety valve.
9
Before lowering the lift ensure that there are no obstructions underneath and that all persons are standing clear.
9
Before storing in safe area, ensure all parts are clean and free of grease and oil. Store lift in the lowest position.
2.
i
INTRODUCTION
tr
A
ll steel construction with foot operated, integral hydraulic pump and ram assembly. Fitted with safety lock device to fix platform at three
Working heights of 660mm, 545mm and 405mm and to prevent accidental lowering. Suitable only for motorcycles with a centre stand or
S
upported on a rear paddock stand. Support platform fitted with full width loading ramp. Base assembly fitted with transport wheels and lock
downs to prevent lift from moving during use.
3. SPECIFICATION
model no: ....................................................................mC454
Capacity: ...................................................................... 450kg
min./max. height: ................................................. 195/660mm
Platform width/length: ........................................ 660/2515mm
maximum load length: .............................................. 1825mm
4. CONTENTS
4.0.1.
Unpack the lift and check contents with list below. Should there be any damaged or missing parts contact your supplier immediately.
4.0.2.
Contents
• Main Assembly
• Sliding Plate
• Leading Plate
• Vice
• Lifting Pedal
• Release Pedal
• Bolts, Washers, Nuts, Cotter Pins
WARNING!
Keep your hands away from moving parts.
Refer to
instruction
manual
Wear safety
footwear
no reaching in Wear protective
gloves
fig.1
mC454| Issue:2 (H,2,F) 15/03/18
Original Language Version
© Jack Sealey limited