4.2.
check the pressure gauge to determine the amount of pressure already in the tyre. The gauge can be used without switching the unit on.
We recommend however the use of a dial pressure gauge for a definitive reading.
check that the compressor on/off switch is in the off position before connecting to the power supply.
MaC04:
Insert the plug into the vehicle’s accessory socket.
iMPortant:
make sure that the maximum current draw is within the
capacity of the accessory socket.
MaC05, MaC06, MaC07:
Connect the terminal clips to the battery, ensuring the correct polarity.
Start the vehicle engine and switch the compressor on. View the pressure gauge to determine when the correct pressure has been
achieved. Switch the compressor off to stop the supply of air.
note:
As the delivery pressure increases, the pump delivery volume will decrease.
4.3.
Unscrew the air hose from the tyre valve. Switch off the vehicle engine. Replace the dust cap onto the valve.
4.4.
After use, disconnect the compressor from the vehicle accessory socket or battery and store it in a safe, dry location.
4.5.
General inforMation
4.5.1.
The time it will take to inflate a tyre will depend upon the amount of air required.
4.5.2.
Should the compressor fail to start when switched on, check the connections and fuse (see section 5.1.)
note:
The compressor may also be used to inflate items such as inflatable dinghies, sports balls, air beds etc. Use the appropriate
inflation nozzle for the item.
Caution:
Some items may not indicate pressure required or the maximum pressure. Be careful not to over-inflate.
note:
The pressure gauge is not a calibrated instrument. It is recommended to use an approved dial pressure gauge for a definitive
reading.
4.6.
The MAC05, MAC06, MAC07 are fitted with a thermal cut-out which will operate after about 30 minutes. If this happens, switch the
compressor off and allow to cool for about 10 minutes.
5. MaintenanCe
5.1.
fuSeS
All the compressors are protected by an automotive style blade fuse. The fuse on the MAC04 is situated in the connector plug,
whereas the larger three models have their fuses housed in the rubber holder which is part of the supply lead.
do not
replace the
fuse with any not of the same specification as the original.
5.2.
filter
An inlet filter is fitted which may be cleaned with mild soapy water. To remove the filter, unscrew the filter housing (fig.1). When
washed, allow the filter to dry and then replace.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St edmunds, Suffolk. iP32 7ar
01284 757500
01284 703534
www.sealey.co.uk
enVironMent ProteCtion
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Weee reGulationS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
note
: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important
: no liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey limited
fig.1
Parts support is available for this product. To obtain a parts listing, email [email protected] or telephone 01284 757500
m
AC04, MAC05, MAC06, MAC07 Issue:2 (H) - 08/03/19
