3. CHARGING
4. OPERATION
Robust lightweight inspection lamp for the professional. Shock, oil and water resistant (IP68) rubber housing with contoured grip
and 360° swivel hook with integral storage. Recessed shatterproof polycarbonate lens with a highly polished reflector board gives
an increased spread of light. Featuring 35 super bright LEDs. 30 LEDs used as an inspection lamp or 5 LEDs in the end for use
as a directional torch. Ideal for use around engine bays and for under body inspections. A unique feature to this unit is the
intelligent charging docking station incorporating inductive charging, so no vulnerable locating pins are required.
Lithium-ion polymer battery (3.7V/2000mAh) for longer life, no memory effect, a much slower discharge than typical Ni-MH
batteries and can operate for up to eight hours on a single charge.
Battery: ..................................3.7V/200mAh Lithium-ion polymer
Operating Time: .....................................................8Hrs
Charging Time: .....................................................................4hrs
Storage Temp: .........................................-20°C ~ 40°C
Operating Temp: ...................................................... -5°C ~ 45°C
Charger Fuse: ........................................................... 3A
Shock / Oil / Water Resistant ...............................................IP68
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycle centre and
disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an
environmentally protective way.
Battery Removal
Pull out the two rubber bungs at the hook end of the lamp.
1.
Undo the 2x screws in the end using a Phillips #1 driver.
2.
Remove complete hook end cap and un-clip the wiring from the main board.
3.
Un-clip battery, remove and dispose of according to local authority
4.
guidelines.
Note: LED arrays are designed to allow individual LEDs to cease functioning
without causing the entire array to fail. This could be as a result of shock or impact.
Shock or impact will invalidate warranty.
4.1
Switch the lamp 'ON & OFF' using the push switch on the handle. Direct the lens
away from your eyes before switching on.
1st press switches on the main 35 x LED inspection lamp.
•
2nd press switches OFF the main 35 x LED inspection lamp and ON the 5 x LED
•
directional torch.
3rd press turns all LED's OFF.
•
4.2
Suspend the lamp by the hanging hook.
When the light is hanging from its hook it can be rotated through 360° for more
precise positioning.
On-Off
Switch
Rotating
Suspension
hook
Charging
Base
Power
Indicator
LED
Lamp
Charging
Indicator
LED.
Note: Fully charge the lamp before first use.
3.1
Plug the charger into the mains supply and turn on, the green LED on the charger will
light to show the charger has power.
3.2
Ensure the lamp is turned off. Insert the lamp into the charger ensuring that the lamp is
in full contact with the charging base (FIG.1), the red LED on the lamp will light to show
charging has begun.
3.3
When the battery has fully charged (approx 4hrs) the red lamp LED will go out.
3.4
When the battery has less than 30 minutes remaining the lamp LED will blink 3 times.
3.5
The lamp will automatically shut down before the battery becomes completely
discharged.
Note: The Lithium battery does not suffer from memory effect and once fully charged may be
stored for up to six months without another charge.
2. INTRODUCTION / SPECIFICATION
FIG.1
Parts support is available for this product.
To obtain parts please email sales@sealey.
co.uk or phone 01284 757500.
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this product.
WARRANTY:
Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION:
For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park
,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
Original Language Version
LED3009 Issue: 2 - 15/03/10
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd
are required to inform potential purchasers of products containing batteries (as
defined within these regulations), that they are registered with Valpak’s registered
compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number
(BPRN) is BPRN00705
